LD 200N Rental - EM Test Load Dump Generator

RENTAL

LD 200N Rental - EM Test Load Dump Generator

Availability: In Stock - Order by 3PM Ships Today!

Automotive Load Dump Generator Features 

      • Clipped Load Dump Generator - ISO 7637: 5a, 5b &7
      • Laptop & ISO 17025 Calibration Included
      • Selectable .5-38 Ohm Impedance (.1 Ohm Steps)
      • Independent Test Generator - Single Unit Solution
      • Free Technical Support & 2 Days Free Transit
      • Built in Coupler - 60volts/30amps (DUT limit)
      • Turnkey Solution - Arrives Ready for Testing!

Overview

The EM Test LD200N provides a effective test solution to ISO 7637-2 pulses 5 and 7, as well as many other international and manufacturer based standards/requirements. This Automotive Conducted Immunity Test Solutions simulate a load dump, the sudden battery disconnection causing an over voltage impulse. This stand alone generator includes an 60v/30a DC coupling decoupling network (CDN) for direct testing and an ISO 17025 accredited calibration, providing a ideal test solution! It is designed for use with 12, 24, or 42 volt supply systems and in conjunction with other EM Test 200 series of generators.

This immunity generator is an all in one system for testing high-energy pulses as required by ISO 7637. By means of a built-in clipping circuit it also generates clipped load dump pulses as per international standards as well as manufacturer requirements. The LD200N can be integrated with the UCS200N and VDS 200N for a complete automotive immunity test system, similar to the NSG 5500.  

This test equipment allows for both pre-programmed standard test and modification of individual pulses through the FreeStyle mode. It has an adjustable source impedance from, 0.5 Ω to 38 Ω in .1 Ω steps. To facilitate a turnkey solution, we include laptop with software with this rental arriving at the testing location ready for use.

LD 200N Accessories/Associated Products

Automotive Load Dump Generator Features 

      • Clipped Load Dump Generator - ISO 7637: 5a, 5b &7
      • Laptop & ISO 17025 Calibration Included
      • Selectable .5-38 Ohm Impedance (.1 Ohm Steps)
      • Independent Test Generator - Single Unit Solution
      • Free Technical Support & 2 Days Free Transit
      • Built in Coupler - 60volts/30amps (DUT limit)
      • Turnkey Solution - Arrives Ready for Testing!

Overview

The EM Test LD200N provides a effective test solution to ISO 7637-2 pulses 5 and 7, as well as many other international and manufacturer based standards/requirements. This Automotive Conducted Immunity Test Solutions simulate a load dump, the sudden battery disconnection causing an over voltage impulse. This stand alone generator includes an 60v/30a DC coupling decoupling network (CDN) for direct testing and an ISO 17025 accredited calibration, providing a ideal test solution! It is designed for use with 12, 24, or 42 volt supply systems and in conjunction with other EM Test 200 series of generators.

This immunity generator is an all in one system for testing high-energy pulses as required by ISO 7637. By means of a built-in clipping circuit it also generates clipped load dump pulses as per international standards as well as manufacturer requirements. The LD200N can be integrated with the UCS200N and VDS 200N for a complete automotive immunity test system, similar to the NSG 5500.  

This test equipment allows for both pre-programmed standard test and modification of individual pulses through the FreeStyle mode. It has an adjustable source impedance from, 0.5 Ω to 38 Ω in .1 Ω steps. To facilitate a turnkey solution, we include laptop with software with this rental arriving at the testing location ready for use.

Data SheetUser ManualRemote Control Manual

Common Standards

SAE J1455, SAE J1113, ISO 7637 – 5a,5b,7, ISO 16750-2, GMW3172

and many other car manufacturer standards

Voltage

20V – 200V  ±  10%

Built in Coupler

60V/30a

Options

Clipped Load Dump Waveform 5b

ISO 7637

Waveforms 5a and 7


Rise Time

5ms – 10ms (10-90%)

Pulse Duration

40-400ms (10-10%)

Internal Resistor

.5 ohm – 38 ohm, selectable in  0.1 ohm steps

Repetition Rage

Min. 30s

Freestyle Mode

 

Rise Time

10µs – 10ms

Pulse Duration

10ms – 1.200 ms

Internal Resistor

Built in 0.5 – 38ohm , selectable in 0.1 ohm steps

Weight

25kg (55lbs)

Dimensions

500mm x 450mm x 290mm (19.68 x 17.71 x 11.41)

Included with Rental

Below you will find a list of common accessories that you can expect to be delivered with the equipment. This is a generic standard list and should you require an exact connector or accessory please contact us prior to order shipping. The laptop that come with the loamp dump generator also come with ISO control software allowing for a quick, turnkey solution.

 

LD 200N

    • Load Dump Generator 
    • Power Cable
    • (4) Safety Lab Cables with Alligator Clips
    • Printed Manual
    • Calibration Documentation 
    • Software License
    • Software on USB Stick/Drive
    • (4) MC Connectors Sets
    • USB Cable
    • 9pin serial cable
    • Shipping Case

EM Test - Automotive Conducted Immunity Generators

 

Description: This video provides an overview on the EM Test conducted immunity test system. The three major components of this automotive EMC test equipment are the LD 200N, UCS 200N, and VDS 200N. This video provides and overview of these test systems including, ISO 7637-2 waveforms covered, accessories that come with equipment, setup, connecting all equipment, and troubleshooting. It also, provides insight into how to setup the software to allow remote testing to be conducted through laptop.

 

Widely Used Standards

This list is a more comprehensive list of all the standards covered with this automotive load dump generator. This is by no means all the standards covered, but the major ones from the largest manufacturers and most widely used standards.

 

  • BMW - (Airbag ECU)
  • BMW 600 13.0 (Part 1)
  • BMW 600 13.0 (Part 2)
  • BMW GS 95002 (1999)
  • BMW GS 95003-2
  • Case New Holland ENS0310
  • Chrysler CS-11979
  • Chrysler PF-9326
  • Claas CN 05 0215
  • Cummins 14269 (982022-026)
  • DaimlerChrysler DC-10842
  • DaimlerChrysler PF-10540
  • EN 300329
  • EN 300340
  • EN 300342-1
  • EN 301489-1
  • EN 301489-17
  • FAW Diesel ECU MY06.0 (Rev.7)
  • Fiat 9.90110
  • Ford EMC-CS-2009.1
  • Ford ES-XW7T-1A278-AB
  • Ford ES-XW7T-1A278-AC
  • Ford FMC1278
  • Freightliner 49-00085
  • GMW 3097
  • GMW 3097 (2001)
  • GMW 3097 (2004)
  • GMW 3100
  • GMW 3100 (2001)
  • GOST 28751-90
  • Honda 3982Z-SDA-0030
  • Hyundai/Kia ES 96100-02 (2006)
  • Hyundai/Kia ES 96200-00
  • Hyundai ES 39110-00
  • ISO 14982
  • ISO 16750-2
  • ISO 7637-1:1990
  • ISO 7637-2:1990
  • ISO 7637-2:2004
  • ISO 7637-2:2011
  • Iveco 16-2103 Rev.15 (2010)
  • Jaguar EMC-CS-2010JLR V1.1 (2011-01)
  • JASO D001-94
  • JASO D902-95
  • John Deere JDQ 53.3
  • Kia/Hyundai ES 95400-10
  • Mack Trucks 606GS15
  • MAN 3285
  • Mazda MES PW 67600
  • MBN 10284-2
  • MBN 22100-2
  • Mitsubishi ES-X82010
  • Nissan 28400 NDS 03
  • Nissan 28401 NDS 02
  • PACCAR CS0016 (1996)
  • Porsche
  • PSA B21 7090
  • PSA B21 7110
  • Renault 36.00.400/B
  • Renault 36.00.400/C
  • Renault 36.00.808/--E
  • Renault 36.00.808/--F
  • Renault 36.00.808/--G
  • Renault 36.00.808/--H
  • Renault 36.00.808/--J
  • Renault 36.00.808/--K
  • SAE J1113-11 (rev.2000)
  • SAE J1113-11 (rev.2007)
  • SAE J1455
  • SAE J2139
  • Scania TB1400
  • Scania TB1700
  • Scania TB1901
  • Smart DE1005B
  • Tata TST/TS/WI/257
  • Toyota TSC7034G
  • Volvo EMC Requirements (1998)
  • Volvo EMC Requirements (2002)
  • Volvo STD 515-0003

I would recommend Transient Specialists. Transient Specialists always provides quality products within the established timeframes. The equipment always meets the specifications and properly shipped within the time frames within the time frames promised.

Scott D., TUV SUD Canada

 

Transient Specialists has been outstanding at working with us for our specialized EMC equipment rental needs. Fast shipments and excellent accommodation for some customized setups. I recommend them highly and they are a pleasure to partner with!

John H., Gates Air, Inc.

 

Laura, I want to thank you and Goran for your excellent customer service and turn around time on the rentals and the calibration documents.  

Adam P., Clark Testing

 

Working for a testing company I deal with renting equipment all the time.  Transient Specialist is the first company I call on my list of rental houses because of their great personnel, prompt delivery of the equipment, knowledgeable and accommodating to the customers needs.

Richard T., National Technical Systems