30Amp Power Supply
VDS200N30 Rental - EM Test Automotive Power Supply
30Amp Automotive Battery Supply Features
- DC Power Supply Dips/Int - ISO 7637: 2b & 4
- Laptop & ISO 17025 Calibration Included
- 15 amp & 30 Amp modules available for delivery!
- Independent Test Generator - Single Unit Solution
- Free Technical Support & 2 Days Free Transit
- Voltage up to 60V & Easily Integrated Into Setup
- Turnkey Solution - Arrives Ready for Testing!
Overview
The EM Test VDS200N series of automotive batter supply/voltage drop simulator provides testing capabilities for a variety of standards including ISO 7637. This series provides provides a diverse set waveforms recommended by both international and manufacturer standards. We offer rentals of both the 15amp (VDS 200N15) and 30amp (VDS 200N30) test solutions which can be used independently or integrated into an EM Test 200 series automotive immunity setup. This piece of test equipment comes with an ISO 17025 accredited calibration and a latop with software installed, providing a quick solution.
The Automotive EMC Test Equipment also allows for both pre-programmed Standard Test and modification of individual pulses. The EM Test iso.control software provides fast control of all test parameters providing and efficient and effective testing solution. This rental equipment comes will all required cords and software required to complete testing. An additional test system the VDS 200N15 with 15 amps is available for rent as well.
This automotive waveform generator can easily be integrated with the UCS200N and the LD200N automotive transient immunity generators for a complete automotive test system, similar to that of the NSG 5500. It provides current up to 200A (peak up to 1,000A) with low output impedance. This EM Test immunity generator provides unique testing capabilities and easy to use interface, making it ideal for a variety of automotive immunity testing needs.
VDS 200N Accessories/Associated Products
Capacitive Coupling Clamp ACC
Automotive Capacitive Coupling Clamp Features
- ISO 7637 and many car manufacturer spec.
- ISO 17025 Calibration Included
- Accept cables up to 40 mm diameter
- Characteristic impedance 50 Ohm
- Solution for Testing Shielded Lines
- Turnkey Solution - Arrives Ready for Testing!
Overview
The EM Test capacitive coupling clamp by EMTest is used to couple pulses to I/O lines required in ISO 7637 waveform 3b and other automotive testing standards. It allows for cable up to 40mm in diameter and has a characteristic impedance of 50 ohms. An ISO 17025 accredited calibration is included in the EMC rental equipment price.
The effective coupling capacitance of the coupling clamp depends on the diameter and the material of the used cables. A typical estimated value can be expected around 100 pF. This clamp is specially designed to meet automotive standards specifically ISO 7637.
The coupling on signal lines of this Automotive EMC Test Equipment can usually not be effected capacitively without interfering with the signal flow. It is often impossible to contact the required circuit (direct), e.g. coaxial or shielded cables. In this case the coupling is realized with the capacitive coupling clamp. The interference simulator can be connected via a coaxial cable on both sides of the ACC coupling clamp.
Load Dump Pulse Generator
Automotive Load Dump Generator Features
- Clipped Load Dump Generator - ISO 7637: 5a, 5b &7
- Laptop & ISO 17025 Calibration Included
- Selectable .5-38 Ohm Impedance (.1 Ohm Steps)
- Independent Test Generator - Single Unit Solution
- Free Technical Support & 2 Days Free Transit
- Built in Coupler - 60volts/30amps (DUT limit)
- Turnkey Solution - Arrives Ready for Testing!
Overview
The EM Test LD200N provides a effective test solution to ISO 7637-2 pulses 5 and 7, as well as many other international and manufacturer based standards/requirements. This Automotive Conducted Immunity Test Solutions simulate a load dump, the sudden battery disconnection causing an over voltage impulse. This stand alone generator includes an 60v/30a DC coupling decoupling network (CDN) for direct testing and an ISO 17025 accredited calibration, providing a ideal test solution! It is designed for use with 12, 24, or 42 volt supply systems and in conjunction with other EM Test 200 series of generators.
This immunity generator is an all in one system for testing high-energy pulses as required by ISO 7637. By means of a built-in clipping circuit it also generates clipped load dump pulses as per international standards as well as manufacturer requirements. The LD200N can be integrated with the UCS200N and VDS 200N for a complete automotive immunity test system, similar to the NSG 5500.
This test equipment allows for both pre-programmed standard test and modification of individual pulses through the FreeStyle mode. It has an adjustable source impedance from, 0.5 Ω to 38 Ω in .1 Ω steps. To facilitate a turnkey solution, we include laptop with software with this rental arriving at the testing location ready for use.
EFT/Microburst Pulse Generator
Automotive Electrical Fast Transient (EFT) Generator Features
- Micropulse Generator Module (ISO 7637, SAE, and NISSAN)
- Laptop & ISO 17025 Calibration Included
- Built-in Battery Switch & Overcurrent Protection
- Independent Test Generator - Single Unit Solution
- Free Technical Support & 2 Days Free Transit
- Built in Coupler Network - 80volts/200amps
- Turnkey Solution - Arrives Ready for Testing!
Overview
The EM Test UCS200N15 series of automotive conducted immunity provides fast transient and microburst testing for SAE J1113, JASO, and ISO 7637-2 waveforms 1,2,3a,3b. This series of products come in a 60 volt, 50 amp (UCS 200N50) version and a 60 volt 100amp (UCS 200N100) Version, both of which can be easily integrated into existing EM Test automotive setups. The built-in coupling network can be used and controlled by any unit of the LD200N, VDS200N and PFM200N series and comes with an A2LA accredited calibration (ISO 17025) is included in the equipment price.
This automotive test equipment is designed to meet many international and car manufacturer specifications from around the globe. Testing parameters can be modified easily through the display or via software. This Automotive EMC Test Equipment goes beyond standard's requirements waveform parameters of the Micropulse generator can be varied in a wide range by means of the FreeStyle mode.
This Teseq Automotive EMC generator includes an innovative color touch screen with intuitive menu structure and defined keys for Start / Stop / Pause, indicated by LED bars, enables the user to program test routines quickly and accurately. The UCS 200n50 also includes built in battery switch an over current protection for added testing safety. This test system can be integrated with the LD200N and VDS200N automotive transient immunity generators for a complete immunity test system, similar to that of the NSG 5500.
Load Resistors EFT/Burst Verification
Verification Kit Features
- Calibration kit as per IEC 61000-4-4
- Also used as per ISO 7637, Annex D
- 50ohm & 1,000ohm Load Resistor Included
Overview
This product made by EM Test is a set of Adapters for verifying EFT/Burst generators. The pulse shape of EFT/burst generators designed as per IEC 61000-4-4 have to be verified both into a 50ohm and a 1,000ohm load at the 50ohm coaxial HV output as well into 50ohm load at the output of the coupling network where the DUT is connected when testing mains supply lines. The CA EFT kit includes the load resistors and a set of adapter to connect the coaxial matching resistors appropriately to the DUT output port.
Waveform Verification Devices
Burst/EFT Pulse Verification Kit
- Verification/calibration kit for IEC/EN 61000-4-4
- For peak voltages up to 8.8 kV
- INA 265B: 50 Ω termination
- INA 266A: 1 kΩ termination
- Turnkey Solution - Arrives Ready for Testing!
Overview
The Teseq CAS3025 burst/EFT pulse verification kit has been specially designed to comply with the new requirements of IEC/EN 61000-4-4:2004 to enable EMC engineers to verify their burst/EFT test generators periodically. Many EMC standards call for a verification of the test equipment before and after every test session. If the verification shows differing results, no valid test results can be assumed and the test equipment has to be re-calibrated.
Auto Arbitrary Pulse Generator
Automotive Battery Supply Generator Features
- 60GB 4-channel Arbitrary Waveform Generator
- Laptop & ISO 17025 Calibration Included
- Dual-Processor-Technology, 500kS/s sample rate
- Simultaneous Recording/Generation Functions
- Free Technical Support & 2 Days Free Transit
- Library of standard test routines & Pseudo-random function
- Turnkey Solution - Arrives Ready for Testing!
Overview
The EM Test Arbitrary waveform generator (auto wave) is used to simulate batteries and many electrical occurrences under field conditions with 4-channel arbitrary generator and a 2-channel transient wave recorder . This Immunity test product Generates and records automotive waveforms ideal for automotive standards including SAE J1113-2 & ISO 16750. This automotive pulse generator can be easily integrated into existing EM Test automotive immunity setups and comes with an ISO 17025 accredited calibration. This product can also be used in conjunction with the Teseq PA 5840 for a OEM LV 124 test solution.
This immunity generator can be used in combination with VDS 200n models or any programmable DC source with 5/10VDC signal output. Autowave.control is a software developed to control the functions of this product. It provides a library of test routines per various manufacturer specifications. By means of autowave.control the user can program any kind of waveform either composed from segments or points and download into the test system.
This Automotive EMC Test Equipment has Enhanced graphic tools are at hand to adjust the waveform according to individual requirements. Autowave.control provides a library of an extensive compilation of predefined segments as well as a large number of test routines as per various manufacturer specifications. This product combines 4-channel arbitrary generator and a 2-channel transient wave recorder into a compact unit.
EFT/Microburst Pulse Generator
Automotive Electrical Fast Transient (EFT) Generator Features
- Micropulse Generator Module (ISO 7637, SAE, and NISSAN)
- Laptop & ISO 17025 Calibration Included
- Built-in Battery Switch & Overcurrent Protection
- Independent Test Generator - Single Unit Solution
- Free Technical Support & 2 Days Free Transit
- Built in Coupler Network - 80volts/200amps
- Turnkey Solution - Arrives Ready for Testing!
Overview
The UCS200N100 by EM Test is a fast transient and microburst generator for waveforms 1,2,3a,3b of SAE J1113, JASO, ISO 7637 and many others. The built-in coupling network can be used and controlled by any unit of the LD200N series, VDS200N series and PFS200N series. ISO 17025 A2LA accredited calibration is included in the EMC rental equipment price. This series of products come in a 60 volt, 50 amp (UCS 200N50) version and a 60 volt 100amp (UCS 200N100) Version, both of which can be easily integrated into existing EM Test automotive setups.
The UCS200N 100 series is equipped to meet all international and car manufacturer specifications from around the globe. Testing parameters can be modified easily through the display or via software. This Automotive EMC Test Equipment goes beyond standard's requirements waveform parameters of the Micropulse generator can be varied in a wide range by means of the FreeStyle mode.
An innovative color touch screen with intuitive menu structure and defined keys for Start / Stop / Pause, indicated by LED bars, enables the user to program test routines quickly and accurately. This automotive generator also includes built in battery switch an over current protection for added testing safety. The UCS200N can be integrated with the LD200N and VDS200N for a complete immunity test system, similar to that of the NSG 5500.
Verification/Calibration Set
Conducted Immunity Generator Features
- Load Resistor 1Ohm & 100Ohm - Power Lines Verification
- Direct Connection into the PFM 200N Series
- Software procedure for verification with CA LV124 loads
- High precision load resistors 1.0, 100 and 1000 ohms
- Arrives Ready for Testing!
Overview
Verification set for the PFM 200N Series for verifying the Pulses E10 & E13 of LV 124.The CA LV 124 set includes four load resistors for the verification of the pulses E10 and E13 of the LV 124 (2013). The load resistors CA LV124-P1R and CA LV124-P100R are used for power line verification. For verification the 16 signal and data lines the CA LV124-D1R and CA LV124-D1000R are used
Automotive OEM Transient System
LV 124 & LV 148 EM Test System
Overview
This is a combination system of the EM Test VDS200N (either 15amp or 30 amp version), Autowave, & PFM 200N. It is designed to test for LV 124 & LV 148 for a variety of required pulses. This equipment can be rented as a turnkey solution, or individually as individual components to supplement existing capabilities. This test system comes with an ISO 17025 accredited calibration and laptop to facilitate a turnkey solution.
100Amp LV124 Transient System
LV 124 EM Test/Teseq System
- Many Pulses of LV124 & Other OEMs
- Laptop & ISO 17025 Calibration Included
- Includes - Accessory Kit, Autowave, & PA 5840
- Free Technical Support & 2 Days Free Transit
- Library of standard test routines
- Turnkey Solution - Arrives Ready for Testing!
Overview
This is a combination system of the Teseq PA 5840 (100amp or less), Autowave, LV 124 calibration fixtures, and a laptop. It is designed to test for LV 124 for a variety of required pulses up to 100amps. This equipment can be rented as a turnkey solution, or individually as individual components to supplement existing capabilities. This test system comes with an ISO 17025 accredited calibration and laptop to facilitate a turnkey solution.
GMW 3172 Transient System
GMW 3172 EM Test System
Overview
This is a combination system of the EM Test VDS200N (either 15amp or 30 amp version), Autowave, & required cabling. It is designed to test for GMW 3172 for a variety of required pulses. This equipment can be rented as a turnkey solution, or individually as individual components to supplement existing capabilities. This test system comes with an ISO 17025 accredited calibration and laptop to facilitate a turnkey solution.
