Surge/Combination Wave - Multifunction Generators Rentals
Surge/Combination Wave - Multifunction Generators Rentals
EN/IEC 61000-4-5 - 2014 relates to immunity requirements for unidirectional surges caused by over-voltages from switching and lightning transients. This standard defines ranges of test levels, test equipment, test setups, and test procedures for equipment under test (EUT). The goal of this International Electrotechnical Commission (IEC) standard is a reproducible guide to evaluate equipment when exposed to this type of phenomena. It specifies that direct injections of lightning currents (direct lightning strikes) are not considered in this standard. The most recent 2014 version 3 cancels out previous publications and gives specifications for 10/700 µs combined wave generator. The most changes from version 2 fall underneath the test procedures section of the standard. This Standard can be purchased on the IEC Webstore.
EN IEC 61000-4-5 Peak to Peak and Voltage Test Levels
This IEC standard is based on a surge, a transient wave of electrical current, and is tested for by Immunity Test Equipment. This standard defines two Combination Wave pulses (Open Circuit Voltage and Short Circuit Current). It set the number of pulses from the EMC test equipment to a.c. ports, d.c. ports, and interconnection lines, at 5 positive and 5 negative (a.c. at 0°, 90°, 180°, & 270°). The time per each pulse must be one minute or less and the EUT must be under operating conditions while the EMC testing is occurring.  EN IEC 61000-4-5 Open and Short Circuit Waveforms
For EN/IEC 61000-4-5 combination wave/surge rentals we offer a variety of different EMI test equipment suppliers including Teseq, EMC Partner, EM Test, Haefely, and many others to meet customer requirements and preferences. These products all have the capability to meet the surge requirements and each have unique testing and reporting capabilities. The most common rental units for surge testing are the NSG 3060, Axos 8, NX5, and UCS500n7. We also provide many accessories that may be required to complete unique and specific testing requirements. These EMI surge products come with an A2LA accredited calibration and free technical support included with the rental. EN IEC 61000-4-5 Surge Rental Products Picture

IEC 61000-4-5 - Surge/Combination Wave Generators

Showing 10 to 18 of 31 products

RENTAL

The UCS500n5 by EM Test is an EMI test generator to 5.5kV EFT and 5kV surge with a built-in single phase coupler. A2LA accredited calibration is included in the EMC rental equipment price. This immunity test product can be operated manually from the front panel or by remote via the built-in USB or GPIB interface.

This EM Test Immunity Test Generator can be operated via Front panel menu and function keys enable the user to program his test routines quickly and accurately. Fail inputs allow to control an ongoing test sequence based on the status of the DUT. Monitoring outputs (BNC) are offered for easy signal measurement and verification. 

The UCS 500N5 includes both pre-programmed standard tests and a quick start menu allowing for parameters to be changed on-line during the test to evaluate the susceptibility level of an individual DUT. This EMC rental product is designed to test to EN/IEC 61000-4-4, EN/IEC 61000-4-5EN/IEC 61000-4-11CE Mark, and many others. The application areas for this immunity test product include telecom, medical, and components. 

RENTAL

The EMC Partner TRA3000 C  Rental is an EMI test generator is an all in one unit testing solution for both the long/short tests. This EMC Partner product includes single phase CDN for EN IEC 61000-4-16 and external box for the 300 volt short test. A2LA accredited calibration is included in the EMC rental equipment price. This products "Plug and Play" architecture allows for system to automatically identify hardware then re-configure testing menu to reflect the change.

This Immunity Test Generator has been created for CE transient testing as well as fulfilling IEC basic standard requirements. The TRA 3000C includes both an Ethernet Port for control communication and test reporting that includes laboratory environmental conditions.This EMC tester is a environmentally conscience solution with low power consumption, less noise, and less heat. 

The TRA3000C is a single unit testing system for EN IEC 61000-4-4EN IEC 61000-4-5EN IEC 61000-4-11CE Mark, and EN IEC 61000-4-16. This product offers many solutions for common standards providing customers with flexibility. As an added bonus EMC Partner does not require proprietary software all reports are HTML based and can be viewed with web browsers.

RENTAL

The combination of the NSG 3060 with the CDN 3061 provides the pulse capabilities for electrical fast transients 4.8kV, surge/combination wave to 6.6kV, 100kHz ringwave to 6.6kV and offers solutions for both IEC, CE mark, & ANSI testing. The NSG 3060 can be rented individually or, as in this case, with a single phase coupler. It allows coupling EFT, surge, and ringwave up to 270V/16A. An A2LA accredited calibration is included in the EMC test equipment price.

This Teseq system offers a user friendly design to help streamline testing to EN/IEC 61000-4-4, EN/IEC 61000-4-5, EN 61000-4-12,ANSI C62.41, C62.45, and UL 1449.  It offers a a 7" color screen and easy to manage user-interface allowing for easy adjustments with the thumb-wheel.  Expansion capabilities enable the system to be configured for a much broader range of applications including 10/700 Telecom Surge and Magnetic Field tests. We also offer rentals of many accessories including the CDN 3083 series to facilitate additional testing capabilities.  

Dips and Interrupts available per IEC 61000-4-11 with optional INA 6502. The automated single-phase coupling network incorporates surge and burst coupling for continuous EUT currents of up to 16 A and complies to the requirements for the surge standard IEC/EN 61000-4-5, as well the coupling modes given in the ANSI C62.45 standard and for burst standard IEC/EN 61000-4-4.

RENTAL

The Teseq CDN 3063 EMC Immunity Tester with the NSG 3060 for EFT to 4.8kV, Surge to 6.6kV, 100 kHz Ringwave to 6.6kV.  It Includes, three phase EFT and Surge coupler with 480V, 32A EUT capability. This is the combination of both the CDN 3063 and NSG 3060 which are priced and often rented desperately. This product is designed primarily for cable-borne transient interference tests.

This Immunity Testing System was created for maximum reliability in a wide range of test setups. Over temperature protection, which allows short term operation at currents exceeding the nominal rating, prevents damage to internal components. The combination of both the NSG 3060 and CDN 3063 takes into account EUT power voltage levels allowing for testing to ANSI C62.41 and many others.

RENTAL

The EMC Partner TRA3000 EMI pulse generator (Optional: Common Mode or Dips/Interrupts) is an all in one unit testing solution for testing EFT to 4.4kV and Surge to 4.1kV with built-in single phase coupler. A2LA accredited calibration is included in the EMC rental equipment price. This products "Plug and Play" architecture allows for system to automatically identify hardware then re-configure testing menu to reflect the change.

This Immunity Test Generator has been created for CE transient testing as well as fulfilling IEC basic standard requirements. This EMC Patner pulse generator includes both an Ethernet Port for control communication and test reporting that includes laboratory environmental conditions. It is a environmentally conscience solution with low power consumption, less noise, and less heat. 

The TRA3000 is a single unit testing system for EN/IEC 61000-4-4, EN/IEC 61000-4-5and CE Marking. With the common mode or dips/interrupts available for testing to EN/IEC 61000-4-11 and EN/IEC 61000-4-16, this design offers flexibility depending on testing needs. As an added bonus EMC Partner does not require proprietary software all reports are HTML based and can be viewed with web browsers.

RENTAL

The Teseq CDN 3063 coupling decoupling network allows for 32Amp 480Volt three phase, EFT, Surge, and 100kHz ringwave for use with the NSG 3040 and NSG 3060. This testing accessory can be rented individually or together as an NSG3060 CDN3063 combination. This accessory is designed for maximum reliability in a wide range of test setups. 

This immunity test equipment includes both IEC and ANSI coupling methods. It also includes a Phase Rotation indicator ensuring correctly sequenced power connection, preventing damage to equipment under test (EUT). An A2LA accredited calibration is included in the EMC test equipment price.

The CDN3063 allows for coupling for testing to EN/IEC 61000-4-4, EN/IEC 61000-4-5, EN/IEC 61000-4-12, ANSI C62.41, ANSI C62.45, and UL 1449. Through new technology it offers the ANSI C62.41 coupling method, used to measure and track the mains voltage and simultaneously control the pulse phase angle. We also offer rentals of higher current and voltage networks including the CDN3083-S100 and CDN3083-B100. 

SALE/RENTAL

Thermo Keytek module for ECATS.  The E 4554 A is three-phase ac line coupler/decoupler for surge and EFT modules requires the E103 controller, and a transient generator module, the E501b surge module, E411 EFT module or the E503 ringwave module can be rented / purchased at an additional cost.

Add to cart

RENTAL

Thermo Keytek three phase ac line coupler/decoupler for surge testing to 10kV and EFT testing with the ECAT system, requires the E103 controller.

RENTAL

The ECAT E103, E502 by Thermo Fisher/Keytek is designed to test to Telecommunications EMC standards requiring 6kV surge of 10x700µs or 9x720µs. This ECAT System comes with an A2LA accredited calibration and free technical support included with rental. This rental is a combination of the ECAT E103 control unit and E502 B modules.

This Thermo Fisher Scientific / Keytek EMC immunity generator provides single port testing and allows changing tests modes without switching off power to the equipment under test (EUT). This helps testing with to be conducted efficiently without re-initializing the EUT between tests. The ECAT E502 B can be rented individually or in combination with the ECAT E103. 

This ECAT system is designed to test EN/IEC 61000-4-5 ed.3, FCC part 68, ITU k.17,ITU-T k.20, ITU-T k.21 and many other immunity standards that have a high voltage telecom surge component. The modular system of this Thermo Fisher / Keytek product provides the ability to be upgraded providing the ability to upgrade test capabilities to meet the newest standard. The E103 and E502 B combination can be controlled via front panel or through computer using Keytek software. 

Showing 10 to 18 of 31 products