PA 5840 Accessories

Showing 1 to 9 of 12 products

ISO 7637-2 Transient Pulse System

In Stock

Automotive Immunity Generator Features 

      • ISO 7637-2 & OEM - Single Unit Solution!
      • Laptop with Software & ISO 17025 Calibration
      • Includes - +ARB, LD5550, MT5511, & Software
      • Free Technical Support & 2 Days Free Transit
      • PA 5480 (Batter Simulators) - 25A & 100A Rentals
      • Prorated Daily Rate After First Month
      • Turnkey Solution - Arrives Ready for Testing!

Overview

The Teseq NSG 5500 rental offers solutions for transient immunity testing based on ISO 7637-2 pulses 1, 2a, 3a, 3b, and the load dump pulses from ISO 16750-2.  It includes the +ARB Option for pulses 2b and 4. Our rental systems also have built in the MT5511, LD5550, +ARB, and come with Autostar Software with a laptop to control the unit(s). All of our automotive rentals include an accredited calibration in the rental price. This Teseq automotive transient generator includes a coupler/battery switch for testing requiring battery coupling. 

The NSG 5500 system allows for testing to international, commercial, and company specific standards including. The Arbitrary waveform generator option supports >64,000 segments plus 1GB of Clone data with up to 10Ms/s 16 bit operation. Control of the testing parameters is done through PC running AutoStar™ software. This Teseq automotive immunity generator rental offers testing to be completed through a single output connector.

This turnkey product comes with a laptop with software pre-installed for efficient testing. Additional inputs and outputs are located on the rear panel for test execution control purposes and monitoring. It is the first product to offer a completely internal 100 amp. battery switch for transient immunity testing. These rental transient immunity generators can be used with the PA 5840-300 battery Simulator or the PA 5840-75 Battery Simulator.

4-Channel Arbitrary Pulse Generator

In Stock

Automotive Battery Supply Generator Features 

      •  60GB 4-channel Arbitrary Waveform Generator 
      • Laptop & ISO 17025 Calibration Included
      •  Dual-Processor-Technology, 500kS/s sample rate
      • Simultaneous Recording/Generation Functions
      • Free Technical Support & 2 Days Free Transit
      • Library of standard test routines & Pseudo-random function
      • Turnkey Solution - Arrives Ready for Testing! 

Overview

The EM Test Arbitrary waveform generator (auto wave) is used to simulate batteries and many electrical occurrences under field conditions with 4-channel arbitrary generator and a 2-channel transient wave recorder . This Immunity test product Generates and records automotive waveforms ideal for automotive standards including SAE J1113-2 & ISO 16750. This automotive pulse generator can be easily integrated into existing EM Test automotive immunity setups and comes with an ISO 17025 accredited calibration. This product can also be used in conjunction with the Teseq PA 5840 for a OEM LV 124 test solution.

This immunity generator can be used in combination with VDS 200n models or any programmable DC source with 5/10VDC signal output. Autowave.control is a software developed to control the functions of this product. It provides a library of test routines per various manufacturer specifications. By means of autowave.control the user can program any kind of waveform either composed from segments or points and download into the test system.

This Automotive EMC Test Equipment has Enhanced graphic tools are at hand to adjust the waveform according to individual requirements. Autowave.control provides a library of an extensive compilation of predefined segments as well as a large number of test routines as per various manufacturer specifications. This product combines 4-channel arbitrary generator and a 2-channel transient wave recorder into a compact unit. 

Load Dump Verification Device

In Stock

Load Dump Verification Equipment 

      • Includes all required load resistor values
      • Resistors with very low inductance
      • Highly accurate resistors (+/-1%)
      • Free Technical Support & 2 Days Free Transit
      • Resistor values 0.5ohm, 1ohm, 2ohm, 4ohm, 10ohm, 20ohm and 50ohm

Overview

This EM Test resistor box containing all load resistors required to verify automotive micropulse and load dump generators. In accordance with the pulse verification requirements given in Annex C of ISO 7637-2:2011 and Annex A of ISO 16750-2:2012, test pulses generated by automotive transient generators need to be verified both under no-load (open circuit verification) and loaded conditions with specified loads. The values of the load resistors is specified and are equal to the generator's internal source impedance defined for the corresponding test pulse. 

Load Resistors EFT/Burst Verification

Verification Kit Features 

      • Calibration kit as per IEC 61000-4-4
      • Also used as per ISO 7637, Annex D
      • 50ohm & 1,000ohm Load Resistor Included

Overview

This product made by EM Test is a set of Adapters for verifying EFT/Burst generators. The pulse shape of EFT/burst generators designed as per IEC 61000-4-4 have to be verified both into a 50ohm and a 1,000ohm load at the 50ohm coaxial HV output as well into 50ohm load at the output of the coupling network where the DUT is connected when testing mains supply lines. The CA EFT kit includes the load resistors and a set of adapter to connect the coaxial matching resistors appropriately to the DUT output port.

Capacitive Coupling Clamp ACC

In Stock

Automotive Capacitive Coupling Clamp Features 

      • ISO 7637 and many car manufacturer spec.
      • ISO 17025 Calibration Included
      • Accept cables up to 40 mm diameter
      • Characteristic impedance 50 Ohm
      • Solution for Testing Shielded Lines
      • Turnkey Solution - Arrives Ready for Testing! 

Overview

The EM Test capacitive coupling clamp by EMTest is used to couple pulses to I/O lines required in ISO 7637 waveform 3b and other automotive testing standards. It allows for cable up to 40mm in diameter and has a characteristic impedance of 50 ohms. An ISO 17025 accredited calibration is included in the EMC rental equipment price.

The effective coupling capacitance of the coupling clamp depends on the diameter and the material of the used cables. A typical estimated value can be expected around 100 pF. This clamp is specially designed to meet automotive standards specifically ISO 7637.

The coupling on signal lines of this Automotive EMC Test Equipment can usually not be effected capacitively without interfering with the signal flow. It is often impossible to contact the required circuit (direct), e.g. coaxial or shielded cables. In this case the coupling is realized with the capacitive coupling clamp. The interference simulator can be connected via a coaxial cable on both sides of the ACC coupling clamp.

Common Mode Test Equipment

Isolation Transformer 14A

      • Isolation transformer 60 dB
      • Meets the requirements of IEC/EN 61000-4-16
      • Three models available
      • Turnkey Solution - Arrives Ready for Testing!

Overview

The Isolation Transformer (ITF) provides the 60 dB decoupling as required in IEC/EN 61000-4-16. The ITF is placed between coupling network and mains. It can be used for a mains frequency in the range 47 to 63 Hz. Three types are available, ITF 6A for 6.5 Amps, ITF 14A for 14.4 Amps and ITF 22 for 21.7 Amps.

NSG 5500 & PA 5840 Immunity System

In Stock

Automotive Immunity Test System Features 

      • ISO 7637-2 & OEM Standards - Single Solution
      • Laptop with Software & ISO 17025 Calibration
      • Includes - NSG 5500, PA 5840, & ACC Clamp
      • Free Technical Support & 2 Days Free Transit
      • PA 5480 (Batter Simulators) - 25A & 100A Rentals
      • Prorated Daily Rate After First Month
      • Turnkey Solution - Arrives Ready for Testing!

Overview

The Teseq NSG 5500, PA 5840, and automotive coupling clamp (conducted immunity system) are designed for ISO7637-2 (pulses 1-7) and a variety of manufacturer (OEM) standards. This system is a combination of three different Automotive EMI products providing a complete test system. Each one of the major components can be rented individually, comes with a laptop, and is calibrated to ISO 17025. We offer rentals, as short as a week, providing a cost effective solution for a short term testing need.

Verification/Calibration Set

Conducted Immunity Generator Features 

      • Load Resistor 1Ohm & 100Ohm -  Power Lines Verification
      • Direct Connection into the PFM 200N Series
      • Software procedure for verification with CA LV124 loads
      • High precision load resistors 1.0, 100 and 1000 ohms
      • Arrives Ready for Testing!

Overview

Verification set for the PFM 200N Series for verifying the Pulses E10 & E13  of LV 124.The CA LV 124 set includes four load resistors for the verification of the pulses E10 and E13 of the LV 124 (2013). The load resistors CA LV124-P1R and CA LV124-P100R are used for power line verification. For verification the 16 signal and data lines the CA LV124-D1R and CA LV124-D1000R are used

VDS200N, Autowave, & PFM 200N System

LV 124 & LV 148 EM Test System

      • Many Pulses of Both Standards LV124 & LV148
      • Laptop & ISO 17025 Calibration Included
      • Includes - VDS200N, Autowave, & PFM 200N
      • Free Technical Support & 2 Days Free Transit
      • Library of standard test routines
      • Turnkey Solution - Arrives Ready for Testing! 

Overview

This is a combination system of the EM Test VDS200N (either 15amp or 30 amp version), Autowave, & PFM 200N. It is designed to test for LV 124 & LV 148 for a variety of required pulses. This equipment can be rented as a turnkey solution, or individually as individual components to supplement existing capabilities. This test system comes with an ISO 17025 accredited calibration and laptop to facilitate a turnkey solution.

 

Showing 1 to 9 of 12 products