Amplifier Research 60S1G6 - Rent 60W 700 MHz - 6 GHz Amplifier

AR 60S1G6 Amplifier:

  • 700 MHz - 6 GHz 60 Watts Psat (min)
  • Class A Broadband Power Amplifier
  • 50 Watts P1dB Power (min)
  • Front Panel Gain Control LCD Display
  • Full VSWR– Tolerant & Portable

Options/Equipment


Get weekly, two week, and monthly rentals on all products

Got Questions about the equipment? Get technical support

Two FREE days transit time with every rental

Request A Quote

Related RF Immunity Equipment

Description

Description

The Model 60S1G6 is a solid-state, Class A design, self-contained, air-cooled, broadband amplifier designed for applications where instantaneous bandwidth, high gain and linearity are required. Housed in a stylish contemporary cabinet, the unit is designed for benchtop use, but can be removed from the cabinet for immediate equipment rack mounting.

The 60S1G6, when used with a sweep generator, will provide a minimum of 60 W of RF power. Included is a front panel gain control which permits the operator to conveniently set the desired output level. The 60S1G6 is protected from RF input overdrive by an RF input leveling circuit which controls the RF input level to the RF amplifier first stage when the RF input level is increased above 0 dBm. The RF amplifier stages are protected from over-temperature by removing the DC voltage to them if an over-temperature condition occurs due to cooling blockage or fan failure. There is a digital display on the front panel to indicate the operate status and fault conditions if an over-temperature or power supply fault has occurred. The unit can be returned to operate when the condition has been cleared. All amplifier control functions and status indications are available remotely in GPIB/ IEEE-488 format, RS-232 hardwire and fiber optic, USB, and Ethernet. The bus interface connector is located on the back panel and positive control of local or remote operation is assured by a Local/Remote switch on the front panel of the amplifier.

The low level of spurious signals and linearity of the Model 60S1G6 make it ideal for use as a driver amplifier in testing wireless and communication components and subsystems. It can be used as a test instrument covering multiple frequency bands and is suitable for a variety of communication technologies such as CDMA, W-CDMA, TDMA, GSM etc. It is also suitable for EMC Test applications where undistorted modulation envelopes are desired.

The export classification for this equipment is 3A001. These commodities, technology or software are controlled for export in accordance with the U.S. Export Administration Regulations. Diversion contrary to U.S. law is prohibited.

Data SheetUser Manual

Specifications

Rated Output Power:

 

60 watts minimum (0.7–6 GHz)
INPUT FOR RATED OUTPUT:

1.0 milliwatt maximum

POWER OUTPUT @ 3dB COMPRESSION:

Nominal, 80 watts; Minimum, 65 watts

POWER OUTPUT @ 1dB COMPRESSION:

 Nominal, 60 watts; Minimum, 50 watts
FLATNESS: ±1.5 dB typical; ±2.5 dB maximum

FREQUENCY RESPONSE:

0.7–6 GHz instantaneously

GAIN (at maximum setting):

48 dB minimum

GAIN ADJUSTMENT (Continuous Range) :

(Continuous Range; 4096 steps remote) 10 dB minimum

INPUT IMPEDANCE:

50 ohms, VSWR 2.0:1 maximum

OUTPUT IMPEDANCE:

50 ohms nominal

MISMATCH TOLERANCE: 

100% of rated power without foldback. Will operate without damage or oscillation with any magnitude and phase of source and load impedance. See Application Note #27

MODULATION CAPABILITY: 

Will faithfully reproduce AM, FM, or Pulse modulation appearing on input signal.

THIRD ORDER INTERCEPT:

56 dBm typical

NOISE FIGURE:

10 dB typical

HARMONIC DISTORTION:

Minus 20 dBc maximum at 60 watts, (0.7–6.0 GHz)

SPURIOUS:

Minus 73 dBc Typ.

PRIMARY POWER:

90- 132, 180-250 VAC; 50/60 Hz, single phase 550 watts maximum

CONNECTORS:

RF Input: N female

RF Output: N female

You may also like

Recently viewed