Home Automotive EMC Test Equipment Rentals EM Test VDS 200Q100.2

LV 124 Testing with VDS 200Q100.2 & Autowave

EM Test VDS 200Q100.2

Name: EM Test VDS 200Q100.2 - Rent 100 Amp Battery Simulator/Source
Brand: EM Test
Availability: InStock

Rent 100 Amp Battery Simulator

In Stock & Ready To Ship

Orders by 3pm ship today

The EM Test VDS 200Q100.2 is a programmable automotive battery supply simulator delivering up to 100 A continuous and 300 A peak for voltage variations, dips, interruptions, and ISO 7637 testing.

Features

-20 to +80 Volts 100 Amps Continuous

Pulses 4 and 2b (ISO 7637-2/ISO 16750-2)

Extended Range 80 Volts 80 Amps

iso.control Software Included

Current ISO 17025 Accredited Calibration

Up to 4 Free Days of Transit Time

Two transit days each way are excluded from rental period

Description

The VDS 200Q series is used to simulate the various battery supply waveforms recommended by international standards and by car manufacturer requirements. Especially the manufacturer requirements are an important area covered by the VDS 200Q series as there is a large variety of requirements. Secondly, the VDS 200Q series serve as powerful DC voltage supplies for the DUT during the tests with automotive transients. The VDS 200Q series covers all three supply voltage categories (48 V, 24 V and 12 V). Their current capability ranges up to 100 A or more depending on the model and your application.

Specifications:
Output Voltage: - 20 Volts to +80 Volts
Output Current: 0A to 100A, continuous
Peak Current: 300 A for 200 ms
Frequency Range: DC to 150 kHz full signal
: 150 kHz to 250 kHz (40 Vpp max.)
Supply Voltage: 3-phase 200/400V +/- 10% (L1, L2, L3, PE)
Weight: 275 kg�
Dimensions: 19"/25 HU*)
COMMON DATA (ALL MODELS)
Operation�: 4- quadrant, Bipolar operation
Source impedance: Zi = Programmable <10mohm, 10-200mOhm selectable
Current limiter: 3x Imax: allows an inrush current of three times nominal current for 200 ms before the current limiter starts 3x ictrl: allows an inrush current of three times the programmed current for 200 ms before the current limiter starts Peak OFF: no inrush current above the set current value (not available for VDS 200Q10)
�Compensation: STD: DC - 40 kHz
: HF: DC - >=150 kHz
: CAP: DC - 3kHz
Output rise time: UR <10 mVp-p, frequency min. 400 Hz
Control�: Analog In
TRIGGER
Automatic: Automatic release of the events

Manual: Manual release of a single pulse
External: External release of a single pulse
OUTPUT
DUT Supply +/-: Safety laboratory or high current connectors
Ext. trigger: 5-15V TTL; BNC connector
CRO Trigger: 5V TTL-signal for oscilloscope
TEST ROUTINES FOR ARBITRARY WAVES
DC source: Max. 60V; current depending on VDS 200N model
Functions: Sine Wave Sweep
: Sine Wave (Cranking)
: Clipped Load Dump
: Jump Start
: Extern
: GM 9105P Pulse 4
: Drop and Jump pulse
Standard Test routines: ISO 7637, Pulses 2b and 4 ISO 16750-2 Jaso Test 1
Service: Service, Setup, Self test
INTERFACE
Serial interfaces: USB
Parallel interface: IEEE 488, addresses 1 - 30
Remote control: To connect an external signal generator (10kohm): 0-10V / 0-50kHz max. 0.5V(p-p) / 0-100kHz