MIL-STD-461G CS117 Rentals - Transient Test Systems
MIL-STD-461 CS115
Impulse Excitation Equipment
MIL-STD-461 CS116
Sinusoidal Transient Rentals
50UH LISNS
Rent 50uH LISNs
5uH LISNs/AN
Rent 5uH LISNs/ANs
ALL SUSCEPTIBILITY EQUIPMENT
View Rental Systems
- RTCA/DO-160 Section 22, Level 3 & CS117 Lvl.1
- Capabilities for Testing Waveforms 1 - 6
- Includes CN-BT7 Injection Probe & TEMA3000 Software
- RTCA/DO-160 Section 22, Level 3 & CS117 Lvl.1
- Capabilities for Testing Waveforms 1 - 6
- Includes CN-BT7 Injection Probe & TEMA3000 Software
- Large aperture 5.5 cm x 8 cm
- Rented With EMC Partner AVI System
- Used as Coupler for 5 Waveforms
- Designed for WF4, WF5A (voltage)
- Level 5 for Single & Multiple Stroke Tests
- Rented with AVI Test Generator
- 3 Double Exponential Pulse 6.4 μs, 70 μs, & 120 μs
- 6 Damped Sinusoidal Pulses 10 kHz - 100 MHz
- Compliant to MIL-STD-461 CS116
- Max 1000 V/150 A DC or 500 V/150 A AC
- HV Compliant to ISO 7637-4 & CISPR 25
- Jumpers Provide LISN Path Configuration
- Frequency 10 kHz – 50 MHz
- 0.25 µF Coupling Capacitor
- Designed for MIL-STD-461D/E/F/G
- Covers 1 MHz to 6 MHz Frequency Range
- Used with Solar 9354-2/-1 Pulse Generators
- Meets Requirements for MIL-STD-461 CS116
- Up to ±7 kV Differential & Common Mode
- 70 MHz Bandwidth (-3 dB)
- Selectable Attenuation 100x/1000x
- Up to ±15 kV Differential or ±1.5 kV Common
- Attenuation 200x or 2000x, 50 MHz Bandwidth
- Rented with Teseq NSG 3150 Test System
- Maximum RMS Current 200 Amps
- Usable Rise time 100 Nanoseconds
- Sensitivity 0.01 Volt/Ampere +1/-0%
- Frequency Range 10 kHz – 30 MHz
- Max 500 Volts AC (600 Volts DC) 100 Amps
- Ideal for MIL-STD-461 Series of Tests
- Exceeds maximum test levels in MIL-STD-461
- Single Generator for CS115 & CS116 Requirements
- Automated Test Routines from Front Panel
CS117 Waveforms & Setup
General Testing Information
MIL-STD-461 CS117 apples to all safety-critical equipment interconnecting cables and non-safety critical equipment with interconnecting cables/electrical interfaces that are part of or connected to equipment performing safety critical functions. The goal is to ensure an EUT ability to withstand lightning transients coupled onto EUT associated cables and power leads. It provides requirements for WF1, WF2, WF3, WF4, WF5A, and WF6 (WF meaning Waveform). Table VII provides limit levels for multiple stroke and multiple burst tests. Below you will find WF1 current waveform and WF2 voltage waveform per MIL-STD-461.
Test Equipment List
- Lightning Transient Generator
- Injection Transformers
- Oscilloscope
- Current monitor probes
- Attenuators, 50 ohm, as needed on current monitoring probes
- Voltage monitor probes, high impedance
- Monitor loop, low impedance wire loop
- Calibration loop, low impedance wire loop
- Capacitors, ≥ 28,000uF for DC power inputs and 10uF for AC power inputs
- LISNs
Calibration Setups
Lightning Transient Generators
MIL-STD-461 CS117 places specific requirements for EMC test equipment based upon required waveforms. This avionic standard also specifies that the power lines are tested separately as well as within the bundle. We offer the AVI 3000 by EMC Partner for rental to test to MIL-STD-461 CS117 level 3. This EMC Partner Immunity product is exclusive in testing to all waveforms required by this standard (1, 2, 3, 4, 5A, and 6). It offers an easy to use interface and includes testing options for DO-160 sec.22 as well. We offer flexible rental terms to meet any testing and provide free technical support.
