ISO 16750-2 Test Equipment - Automotive EMC Rentals
ISO 16750-2 Test Equipment - Automotive EMC Rentals
ISO 16750-2 test equipment rentals provides testing capabilities without expensive capital expenditures. This automotive EMI based standard includes a load dump test requirement. A load dump occurs when a discharged battery disconnects while current is still being generated through alternating, holding all other loads on the circuit constant. ISO 16750 part 2: electrical loads includes testing for direct current supply voltage, overvoltage, superimposed alternating voltage, slow decrease and increase of supply voltage, Discontinuities in supply voltage, and several others. This standard sets the temperature, waveforms, methods, and generators. The four major sections for this standard are electrical, mechanical, climatic, and chemical loads. This standard can be purchased via the ISO website.

ISO 16750 - Load Dump Pulse

ISO 16750-2 unless otherwise specified in the standard it provides guidance on limits for frequency and time: ±5 %, voltages: ±0.2V, and resistance: ±10%. This standard includes a variety of tests they include a voltage drop, load dump, open circuit test, and several others. The load dump testing is split into two different categories, testing with/without centralized load dump suppression. ISO 16750-2 specifies in Annex A, Test load dump pulse generator verification procedure, requirements for test equipment for this automotive standard. The tolerance of the matching resistor is ± 1 % for this automotive standard. To vary that the generator meets necessary requirements it is tested under no load matched load conditions.ISO 16750 Generator Requirments
For ISO 16750-2 testing we offer automotive EMI test equipment rentals from both Teseq and EM TestAll of these immunity generators meet the requirements of ISO 16750-2 and each provides unique testing and reporting methods. We provide flexible rentals terms, as short as a week, to allow customers the most flexibility. The most widely used products include the NSG 5500 and UCS200n/VDS200n/LD200n combinations. The EM Test automotive products offer more flexibility for individual waveform testing. All of our automotive EMC rentals come with an A2LA accredited calibration and free technical support included with the rental. ISO 16750 Rental Product Picutre

ISO 16750-2 Test Equipment - Automotive EMC Rentals

RENTAL

Automotive Immunity Generator Features 

      • ISO 7637-2 & OEM - Single Unit Solution!
      • Laptop with Software & ISO 17025 Calibration
      • Includes - +ARB, LD5550, MT5511, & Software
      • Free Technical Support & 2 Days Free Transit
      • PA 5480 (Batter Simulators) - 25A & 100A Rentals
      • Prorated Daily Rate After First Month
      • Turnkey Solution - Arrives Ready for Testing!

Overview

The Teseq NSG 5500 rental offers solutions for transient immunity testing based on ISO 7637-2 pulses 1, 2a, 3a, 3b, and the load dump pulses from ISO 16750-2.  It includes the +ARB Option for pulses 2b and 4. Our rental systems also have built in the MT5511, LD5550, +ARB, and come with Autostar Software with a laptop to control the unit(s). All of our automotive rentals include an accredited calibration in the rental price. This Teseq automotive transient generator includes a coupler/battery switch for testing requiring battery coupling. 

The NSG 5500 system allows for testing to international, commercial, and company specific standards including. The Arbitrary waveform generator option supports >64,000 segments plus 1GB of Clone data with up to 10Ms/s 16 bit operation. Control of the testing parameters is done through PC running AutoStar™ software. This Teseq automotive immunity generator rental offers testing to be completed through a single output connector.

This turnkey product comes with a laptop with software pre-installed for efficient testing. Additional inputs and outputs are located on the rear panel for test execution control purposes and monitoring. It is the first product to offer a completely internal 100 amp. battery switch for transient immunity testing. These rental transient immunity generators can be used with the PA 5840-300 battery Simulator or the PA 5840-75 Battery Simulator.

RENTAL

The PA5840-300 by Teseq is an 100 Amp DC power supply for use with the Teseq NSG 5500 automotive EMC immunity test system. A2LA accredited calibration is included in the automotive EMI immunity test equipment rental price. This fast, reliable, and modular battery simulator supply comes with up to 18 kW of power and is designed to simulate 12, 24, and 42 V vehicle electrical systems. 

This Automotive EMC Test Equipment provides dips and interrupts for a diverse set of automotive EMI standards including ISO 7637, waveforms 2b and 4. The PA 5840 also allows for testing to military automotive immunity standards including MIL-STD-461E. This latest Teseq model has 4 quadrant operation, important in the EV environment.

The PA 5840 includes two gain settings for use and output ranges for power efficiency. This DC power supply needs a control unit to be used.This automotive transient immunity generators setup also allows for High bandwidth up to 150 kHz. To facilitate the most efficient testing we provide rentals of both the 100 amp and the PA 5840-75 25 Amp model.  

RENTAL

The PA5840-75 by Teseq is an 25 Amp DC power supply for use with the Teseq NSG 5500 automotive EMC immunity test system. A2LA accredited calibration is included in the automotive EMI immunity test equipment rental price. This fast, reliable, and modular battery simulator and is designed to simulate 12, 24, and 42 V vehicle electrical systems. 

This Automotive EMC Test Equipment provides dips and interrupts for a diverse set of automotive EMI standards including ISO 7637, waveforms 2b and 4. The PA 5840 also allows for testing to military automotive immunity standards including MIL-STD-461E. This latest Teseq model has 4 quadrant operation, important in the EV environment.

The PA 5840 includes two gain settings for use and output ranges for power efficiency. This DC power supply needs a control unit to be used.This automotive transient immunity generators setup also allows for High bandwidth up to 150 kHz. To facilitate the most efficient testing we provide rentals of both the 100 amp and the PA 5840-300 100 Amp model.  

RENTAL

Automotive Load Dump Generator Features 

      • Clipped Load Dump Generator - ISO 7637: 5a, 5b &7
      • Laptop & ISO 17025 Calibration Included
      • Selectable .5-38 Ohm Impedance (.1 Ohm Steps)
      • Independent Test Generator - Single Unit Solution
      • Free Technical Support & 2 Days Free Transit
      • Built in Coupler - 60volts/30amps (DUT limit)
      • Turnkey Solution - Arrives Ready for Testing!

Overview

The EM Test LD200N provides a effective test solution to ISO 7637-2 pulses 5 and 7, as well as many other international and manufacturer based standards/requirements. This Automotive Conducted Immunity Test Solutions simulate a load dump, the sudden battery disconnection causing an over voltage impulse. This stand alone generator includes an 60v/30a DC coupling decoupling network (CDN) for direct testing and an ISO 17025 accredited calibration, providing a ideal test solution! It is designed for use with 12, 24, or 42 volt supply systems and in conjunction with other EM Test 200 series of generators.

This immunity generator is an all in one system for testing high-energy pulses as required by ISO 7637. By means of a built-in clipping circuit it also generates clipped load dump pulses as per international standards as well as manufacturer requirements. The LD200N can be integrated with the UCS200N and VDS 200N for a complete automotive immunity test system, similar to the NSG 5500.  

This test equipment allows for both pre-programmed standard test and modification of individual pulses through the FreeStyle mode. It has an adjustable source impedance from, 0.5 Ω to 38 Ω in .1 Ω steps. To facilitate a turnkey solution, we include laptop with software with this rental arriving at the testing location ready for use.

RENTAL

Automotive Battery Supply Generator Features 

      • DC Power Supply Dips/Int - ISO 7637: 2b & 4
      • Laptop & ISO 17025 Calibration Included
      • 15 amp & 30 Amp modules available for delivery!
      • Independent Test Generator - Single Unit Solution
      • Free Technical Support & 2 Days Free Transit
      • Low Output Impedance & Easily Integrated Into Setup
      • Turnkey Solution - Arrives Ready for Testing! 

Overview

The EM Test VDS200N series of automotive batter supply/voltage drop simulator provides testing capabilities for a variety of standards including ISO 7637. This series provides provides a diverse set waveforms recommended by both international and manufacturer standards. We offer rentals of both the 15amp (VDS 200N15) and 30amp (VDS 200N30) test solutions which can be used independently or integrated into an EM Test 200 series automotive immunity setup. This piece of test equipment comes with an ISO 17025 accredited calibration and a latop with software installed, providing a quick solution.

The Automotive EMC Test Equipment also allows for both pre-programmed Standard Test and modification of individual pulses. The EM Test iso.control software provides fast control of all test parameters providing and efficient and effective testing solution. This rental equipment comes will all required cords and software required to complete testing. An additional test system the VDS 200N30 with 30 amps is available for rent as well.

This automotive waveform generator can easily be integrated with the UCS200N and the LD200N automotive transient immunity generators for a complete automotive test system, similar to that of the NSG 5500. It provides current up to 200A (peak up to 1,000A) with low output impedance. This EM Test immunity generator provides unique testing capabilities and easy to use interface, making it ideal for a variety of automotive immunity testing needs.

RENTAL

The EM Test VDS200N30 power supply, and Interrupts is designed for automotive EMC standards including ISO 7637, waveforms 2b an 4. This battery supply simulator and DC voltage source provides a diverse set waveforms recommended by both international and company standards. A2LA accredited calibration is included in the EMC rental equipment price.

This waveform generator can easily be integrated with the UCS200N and the LD200N for a complete immunity test system, similar to that of the NSG 5500. It provides current up to 200A (peak up to 1,000A) with low output impedance. The VDS 200N30 Automotive EMC Test Equipment also allows for both pre-programmed Standard Test and modification of individual pulses. 

RENTAL

Automotive Battery Supply Generator Features 

      •  60GB 4-channel Arbitrary Waveform Generator 
      • Laptop & ISO 17025 Calibration Included
      •  Dual-Processor-Technology, 500kS/s sample rate
      • Simultaneous Recording/Generation Functions
      • Free Technical Support & 2 Days Free Transit
      • Library of standard test routines & Pseudo-random function
      • Turnkey Solution - Arrives Ready for Testing! 

Overview

The EM Test Arbitrary waveform generator is used to simulate batteries and many electrical occurrences under field conditions with 4-channel arbitrary generator and a 2-channel transient wave recorder . This Immunity test product Generates and records automotive waveforms ideal for automotive standards including SAE J1113-2 & ISO 16750. This automotive pulse generator can be easily integrated into existing EM Test automotive immunity setups and comes with an ISO 17025 accredited calibration. This product can also be used in conjunction with the Teseq PA 5840 for a OEM LV 124 test solution.

This immunity generator can be used in combination with VDS 200n models or any programmable DC source with 5/10VDC signal output. Autowave.control is a software developed to control the functions of this product. It provides a library of test routines per various manufacturer specifications. By means of autowave.control the user can program any kind of waveform either composed from segments or points and download into the test system.

This Automotive EMC Test Equipment has Enhanced graphic tools are at hand to adjust the waveform according to individual requirements. Autowave.control provides a library of an extensive compilation of predefined segments as well as a large number of test routines as per various manufacturer specifications. This product combines 4-channel arbitrary generator and a 2-channel transient wave recorder into a compact unit.