GMW3097 - Automotive EMC Test Equipment Rentals
Load Dump Simulators
Rent Pulse Generators
Electrical Fast Transient
Automotive Pulse Generators
Programmable Batteries
DC Power Supplies
Conducted RF Systems
BCI Section 3.4
Radiated Immunity Equipment
Amplifiers & Antenna (3.4)
- Test System for ISO 7637-2/3 Requirements
- Battery Simulators Available up to 100 Amps
- Pre-programmed International & OEM Tests
- Includes NSG 5500, PA 5840, & CDN 400
- ISO 7637-2 & ISO 7637-3 Tests
- Battery Simulators up to 60 V 100 A
- Pulses 4 and 2b (ISO 7637-2/ISO 16750-2)
- Maximum 60 Voltage 30 Amps
- Voltage Drop Simulator with Low Output Impedance
- Generators Clipped Load Dump Pulses
- Tests to ISO 7637-2 & ISO 16750-2 Load Dump
- Built-in CDN Max 80 Volts 30 Amps
- -15 to +60 Volts 25 Amps Continuous
- High Bandwidth up to 150 kHz
- 75 Amps Inrush Current Capability
- Micropulse Generator for ISO, JASO, & SAE
- ISO 7637-2 Pulses 1, 2a, 3a, & 3b
- Built-in CDN Max 80 Volts 100 Amps
- Provides LV124 E-01 to E-15 Pulses
- DUT Capabilities up to 100 Amps
- Includes Software & Verification Kits
- 2-channel Arbitrary Waveform Generator
- Dual-Processor-Technology, 500kS/s sample rate
- Library of Standard Test Routines
- Many pulses of LV124/Other OEMs (100A)
- Includes - Accessory Kit, Autowave & PA 5840
- Rent PFM200N100 for Additional OEM Pulses
- 10 kHz to 400 MHz BCI Test Kit
- Includes BCI Probe & Monitoring Probes
- Designed for IEC, ISO, & MIL-STD Tests
- 10 kHz to 230 MHz BCI Test Kit
- Includes BCI Probe & Monitoring Probe
- Designed for IEC 61000-4-6 Current Injection
- -60 to +60 Volts 50 Amps Continuous
- Pulses 4 and 2b (ISO 7637-2/ISO 16750-2)
- Extended Range 80 Volts 40 Amps
- Teseq ISO 7637-3 ICC for UCS 200N Series
- Used for Injection of Pulse 2A
- Includes CIP 9136A, PCJ 9201, & MN-CIP9136
- Teseq ISO 7637-3 ICC for NSG 5500 System
- Used for Injection of Pulse 2A
- Includes CIP 9136A, PCJ 9201, & INA 5580
- Output Max. 160 V p-p, 50 V rms
- Output Current Max. 18 A rms
- Automatic Closed Loop Test Procedures
- Frequency response 10 Hz to 500 kHz
- Audio power up to 3 x 200 W
- Turns ratio 2:1 step down
Overview
Our automotive EMC test equipment rentals provide short-term cost efficient testing solutions for testing to GMW3097 and many other standards. This General Motors standard applies to passenger vehicles, light, and medium duty trucks. This standard is part of a series for General Motors global EMC testing documents, GMW3091, GMW3097 and GMW3103. All testing completed for this automotive standard must also be accompanied by a test plan. This plan determines the classification of testing needed. It separates testing by emission(3.3), immunity(3.4), transients(3.5), and ESD(3.6). For automotive transient testing this standard uses ISO 7637 waveforms as a baseline with modifications, stating "The test equipment shall comply with ISO 7637-1 and ISO 7637-2". The table below lists the basic specification to which the standard references.
Testing
GMW3097 bases the transient immunity test requirements around ISO 7637-2 pulses 1, 2a, 2b, 3a, 3b, 4, 5a, 5b and 7. These pulses are mainly done in in accordance with ISO 7637 with minor modifications. The major difference is the number and time of the pulses. These number and times can be found in Table 18 of the standard. It provides cycle times minimum and maximum values and the number of pulses or application time. This standard also puts forth guidance on how to conduct ESD testing as well. The Electrostatic Discharge (ESD) portion of this standard references ISO 10605 for test equipment and test procedures with minor modifications. The Automotive EMC test equipment must have both an 330pF/2kΩ and 150pF/2kΩ capabilities to 30kV to test to all required levels of GMW3097. The majority of our automotive EMC test equipment rentals provides testing to both the base specifications and this standard.
Equipment
For automotive EMC test equipment rentals to GMW3097 we carry the NSG 5500 and PA5480 by
Teseq, and UCS200N, VDS200N, and LD200N by
EM Test.
The NSG 5500 and PA 5840 provide the most comprehensive testing capabilities allowing for testing to a variety of standards and all of the waveforms of ISO 7637-2. The EM Test automotive immunity products, the UCS200N, VDS200N, and LD200N can be rented individually and provide testing for individual waveform requirements, providing a cost efficient solution. The majority of our automotive rentals come with an computer with software installed providing a turnkey solution. All of our automotive immunity test equipment rentals come with an A2LA accredited calibration and free technical support. Even if the A2LA calibration is not required, it provides the assurance that the test equipment will have the same capacities and outputs as test labs.
