Showing 1 - 16 of 23 products
Quick Access
Return Instructions

Rental Terms


  1. TSI retains title of all equipment. Customers are precluded from altering, assigning, modifying or encumbering the equipment in any way.
  2. Equipment is shipped F.O.B. shipping point and must be returned prepaid and insured to TSI per shipping instructions included with the equipment. Customers are responsible for all taxes and duties related to the lease of the equipment.
  3. The lease is non-cancelable for its initial term and may not be renewed without permission from TSI. If it is renewed, the customer is responsible for all lease charges accrued whether or not the customer has issued additional purchase orders.
  4. In the event that the equipment is non-functional, lease charges are abated from the date that notification is given to TSI, until a replacement unit is furnished to the customer. Notification of a non-functional unit must be given within 72 hours of delivery or the customer will be responsible rental charges accrued between delivery date and the date they notified TSI of a problem. Notification of missing accessories must be given within 72 hours of delivery or the customer will be responsible for the return of all accessories listed on the packing list.
  5. The customer shall bear all risks of loss or damage to the equipment from the time of shipment until TSI receives the equipment in good working order, unless notification is given per sec. 5.
  6. The customer agrees that TSI has not made any representation of warranty, expressed or implied (except as stated in the document) on the equipment and the responsibility for equipment selection, suitability and fitness of use for a particular purpose lies solely with the customer.
  7. The customer will hold TSI harmless from all claims and expenses resulting from the selection, delivery, use and/or possession of any equipment obtained from or through TSI.
  8. In the event of default by the customer of any of the above terms and conditions, TSI shall be entitled to the immediate possession of this equipment.
  9. The customer agrees that the terms and conditions listed here shall supersede any conflicting terms in, or attached to, the purchase order.
  10. This agreement shall be interpreted according to the laws of the State of Illinois. The customer shall pay to TSI all costs and expenses, including reasonable attorneys’ fees, incurred by TSI in exercising any of its rights or remedies with regard to the rental or enforcement of any of these terms and conditions.
FAQs
EM Test CA BS 200N Front Side EM Test CA BS 200N Front
EM Test CA BS 200N - Load Impedance for BS 200N
  • 0.6ohm / 50uH Load as per ISO 7637-2:2004
  • Max Supply Voltage 28VDC
  • Max Load Current 50A
Teseq CDN 500 Front Side Teseq CDN 500 Side
Teseq CDN 500 - Rent ISO 7637-3 Capacitive Coupling Clamp
  • Compliant for ISO 7637-3 Testing
  • Length of Clamp 1000 mm
  • 50 Ohm BNC Connectors 
Schwarzbeck TF 130-150 - Front Side Schwarzbeck TF 130-150 - Side
Schwarzbeck TF 130-150 - Rent Rent Ford Test Fixture
  • Compliant to FORD EMC-CS-2009 
  • Used for RI 130 & RI 150 Immunity Tests
  • Type N Female Connectors on Fixture
EM Test MN-CIP 9136 - Adapter EM Test MN-CIP 9136 - Adapter & Cable
EM Test MN-CIP 9136 - Rent Impedance Matching Network
  • Impedance Network to Achieve Pulse Requirements
  • Used with the EM Test UCS 200N Series
  • ISO 7637-3 Slow Transient Pulse 2A
In Stock
Teseq PA 5740 - Front Side Teseq PA 5740 - Front
Teseq PA 5740 - Rent 10 Amp Battery Simulator
  • -60 to +60 Volts 10 Amps Continuous
  • High Bandwidth up to 180 kHz
  • Four Quadrant Operation
Schwarzbeck NNLK 8129 Front Side Schwarzbeck NNLK 8129 Front
Schwarzbeck NNLK 8129 - Rent 50uH 200 Amp LISN
  • Impedance 50 µH || 50 Ω
  • Frequency Range 150 kHz – 30 MHz
  • Maximum: 200 Amps 700 Volts AC 
Teseq EXT 10uF - Front Side Teseq EXT 10uF mounted on LISN
Teseq EXT 10uF - 10 µF capacitor for RTCA/DO-160G
  • Designed for RTCA/DO-160 Testing
  • 10uF/1000 Volt Capacitor
  • Rented with HV-AN 150 LISN
EM Test BS 200N100 Front Side EM Test BS 200N100 Side Top
EM Test BS 200N100 - Electronic Switch for Voltage Transient Testing
  • Electronic Switch Accordance with ISO 7637 Part 2
  • Rented with EM Test Transient Emissions Set
  • Max 60 Volts & 100 Amps Cont. (400A @ 200ms)
Schwarzbeck HVSE 8600 Front Side Schwarzbeck HVSE 8600 with LISNs Open
Schwarzbeck HVSE 8600 - Automotive Shielded Enclosure
  • Designed for use with NNHV 8123-200
  • Compliant to HV CISPR 25 & BMW GS 95025-1
  • Rented with set of NNHV 8123-200 LISNs
Teseq SME HV-AN 150 - Front Side Teseq SME HV-AN 150 - Front Open
Teseq SME HV-AN 150 - AN Shielded Metal Enclosure
  • Designed for use with Teseq HV-AN 150s
  • Rugged Design using Stainless Steel
  • Compliant to HV CISPR 12/25 & ISO 7637-4
In Stock
Schwarzbeck NNHV 8123-200 Front Side Schwarzbeck NNHV 8123-200 Front
Schwarzbeck NNHV 8123-200 - Rent 5uH 200 Amp DC LISN
  • Max 1000 V/200 A DC or 700 V/200 A AC
  • Includes HVSE 8600 Shielded Enclosure
  • 5uH LISN in Accordance with CISPR 25
Teseq HV-AN 150 Front Side Teseq HV-AN 150 Front Top
Teseq HV-AN 150 - Rent 5uH 150 Amp Artificial Network
  • Max 1000 V/150 A DC or 500 V/150 A AC
  • HV Compliant to ISO 7637-4 & CISPR 25
  • Jumpers Provide LISN Path Configuration
In Stock
EM Test Transient Emissions Test Set - Side Front EM Test Transient Emissions Test Set - Side
Conducted Transient Emissions Set ISO 7637-2 EM Test
  • Electronic Switch, Artificial Network, & RS-Box
  • BS 200N100 Electronic switch, 60V DC/100A
  • AN 200N100 1,000V DC, 250V AC (up to 1kHz)
Teseq ISO 7637-3 ICC Test System - Rental Transient Injection Kit Teseq ISO 7637-3 ICC Test System - Rental Transient Injection Kit
Teseq ISO 7637-3 ICC Test System - Rental Transient Injection Kit
  • Teseq ISO 7637-3 ICC for NSG 5500 System
  • Used for Injection of Pulse 2A
  • Includes CIP 9136A, PCJ 9201, & INA 5580
EM Test AN 200N100 Front Side EM Test AN 200N100 Front Top
EM Test AN 200N100 - Rent 100 Amp 5uH DC LISN
  • Max 1000 Volts 100 Amps DC (150 Amp Peak)
  • ISO 7637-2, ISO 11452-4, & CISPR 25 Compliant
  • Switch for Selecting Testing Requirements
In Stock
EM Test MN-CIP9136 & CIP 9136A EM Test MN-CIP9136 & CIP 9136A v2
EM Test ISO 7637-3 ICC Method - Rental Transient Injection Kit
  • Teseq ISO 7637-3 ICC for UCS 200N Series
  • Used for Injection of Pulse 2A
  • Includes CIP 9136A, PCJ 9201, & MN-CIP9136