Home > MIL-STD-461 & DO 160 - Susceptibility & Emissions Equipment > Solar 7054-1
Solar 7054 - Front Side Solar 7054 - Front Solar 7054 - Back Solar 7054 - Front Top
Solar 7054 - Front Side
Solar 7054 - Front
Solar 7054 - Back
Solar 7054 - Front Top

Solar 7054-1

Rent DO-160G 600 Volt Spike Generator
In Stock - Order by 3 p.m. ships today
  • Output 10 Volts to 600 Volts into 5 Ω or less
  • Compliant Spike Generator to DO-160 sec 17
  • Typically Rented with Solar 2201 Matching Transformer
  • Current ISO 17025 Accredited Calibration
Got Questions? Speak to an Expert +1 630-887-0329
Two FREE days transit with every rental

Related Equipment

In Stock
Solar 2201 - Front Side Solar 2201 - Front
Solar 2201-1
Rent Impedance Matching Transformer
In Stock
Solar 6512-106R - Upright Front Solar 6512-106R - Side
Solar 6512-106R
Rent 10μF Feed-Thru Capacitor
In Stock
Solar LISN 9233 - Front Side 2 Solar LISN 9233 - Back
Solar LISN 9233-50
Rent 50μH 50Amp LISN 10 kHz – 50 MHz
Solar 8610-50 - Front Side Solar 8610-50 - Front
Solar 8610-50
Rent 50uH 500 Volt 100 Amp LISN
In Stock
Solar 6220-4 - Front Side Solar 6220-4 - Front
Solar 6220-4A
Rent 50 Amp 4 kV Isolation Transformer
In Stock
Solar 6220-1A - Front Side Solar 6220-1A - Front
Solar 6220-1A
Rent 50 Amp Isolation Transformer

Description

The peak amplitude of the Solar Model 7054-1 is adjustable from 10 V to over 600 V into 5 Ω. The source impedance is less than 0.5 Ω. The transient shape approximates the curve given in Figure 19 of MIL-STD-462 with less than or equal to 2.0 µS rise time and approximately 10 µS fall time.

On 50, 60 or 400 Hz power lines the transient can be applied in a periodic manner to the negative or the positive half-cycle of the power frequency. The transient's relation to the sine wave may be adjusted in phase from 0° to 360°. For nonsynchronous injection on either AC or DC lines, the repetition rate can be adjusted from 0.8 pulse per second to 10 pulse per second. Single transients can be applied with the pushbutton on the panel.

Two sets of output terminals allow either parallel or series injection into the power line. Series injection may be used on DC and AC lines. Parallel injection is used on DC lines only. The output winding used for series injection can carry 25 A of power current. The output terminals are isolated from the chassis and the power cord.

Spike amplitude:
Continuously adjustable from less than 10 V to more than 250 V peak
Repetition rate:
Continuously adjustable from 0.8 to 10 pulse per second
Rise time:
Less than or equal to 2.0 uS into 5 Ohm resistive load
Spike duration:
Output falls to zero in approximately 10 uS
Spike shape:
See Figure 3. Similar to Figure 19 of MIL-STD-462
Phase adjustment:
Spike position adjustable from 0 to 360 degrees periodically on 50, 60 or 400 Hz sine wave
Internal impedance:
Less than 0.5 Ohms
Output power:
More than 300 kW peak into 0.5 Ohm load
Power current in series injection mode:
Handles up to 25 A of current at power frequencies
Power requirements:
115 V 60 Hz, 1.6 A (230 V 50 Hz, 0.8 A available)
Dimensions, standard rack panel:
19" wide x 7" high x 12.75" deep (48.26 cm x 17.78 cm x 32.38 cm)
Documentation