EM Test UCS 200N50 - Rent Microburst Generator 50 Amp CDN
- Micropulse Generator for ISO, JASO, & SAE
- ISO 7637-2 Pulses 1, 2a, 3a, & 3b
- Built-in CDN Max 80 Volts 50 Amps
In Stock
EM Test CA EFT Kit - Rent EFT/Burst Pulse Verification Kit
- Calibration Kit Designed for EM Test Systems
- Compliant to IEC 61000-4-4 & ISO 7637, Annex D
- Includes KW 50 (50Ω) & KW1000 (1kΩ)
EM Test ACC - Rent Automotive Capacitive Coupling Clamp
- ISO 7637-3 & OEM Compliant Solution
- Accepts Cables up to 40mm Diameter
- Solution for Testing Shielded Signal Lines
In Stock
EM Test CA LV 124 - Rent LV 124 Verification Kit for PFM 200N100
- 10 Ohm & 100 Ohm Power Calibration Loads
- 1 Ohm & 1000 Ohm Data Line Calibration Loads
- Designed for up to 48 Volt Battery Lines
In Stock
Teseq INA 4381 - 150 pF/2 kOhm Discharge Network
- 150 pF/2 kΩ ISO 10605 Automotive Network
- Used with Teseq NSG 437 or NSG 438 Series
- ISO 17025 Calibrations Available
Teseq INA 4382 - 330 pF/2 kOhm Discharge Network
- 330 pF/2 kΩ ISO 10605 Automotive Network
- Used with Teseq NSG 437 or NSG 438 Series
- ISO 17025 Calibrations Available
Teseq INA 4553 - 330 pF/330 Ohm Discharge Network
- 330 pF/330 Ω ISO 10605 Automotive Network
- Used with Teseq NSG 437 or NSG 438 Series
- ISO 17025 Calibrations Available
EMC Partner DN2 - Rent 330 pF/ 2 kΩ Discharge Network
- 30 kV 300 pF/2 kΩ Discharge Network
- Used with ESD3000 ESD Simulator
- Requires RM32 Relay Module
In Stock
EM Test CA ISO - Rent Resistor Kit for Load Dump Verification
- Includes all Required Load Resistor Values
- Resistors with very low inductance
- Highly accurate resistors (+/-1%)
EMC Partner DN3 - Rent 30 kV 150 pF/2 kΩ Discharge Network
- 30 kV 150 pF/2 kΩ Discharge Network
- Used with ESD3000 ESD Simulator
- Requires RM32 Relay Module
In Stock
EMC Partner DN6 - Rent 330 pF/ 330 Ω Discharge Network
- 30 kV 330 pF/330 kΩ Discharge Network
- Used with ESD3000 ESD Simulator
- Requires RM32 Relay Module
In Stock
EM Test ISO 7637-3 ICC Method - Rental Transient Injection Kit
- Teseq ISO 7637-3 ICC for UCS 200N Series
- Used for Injection of Pulse 2A
- Includes CIP 9136A, PCJ 9201, & MN-CIP9136
EM Test AN 200N100 - Rent 100 Amp 5uH DC LISN
- Max 1000 Volts 100 Amps DC (150 Amp Peak)
- ISO 7637-2, ISO 11452-4, & CISPR 25 Compliant
- Switch for Selecting Testing Requirements
In Stock
Teseq ISO 7637-3 ICC Test System - Rental Transient Injection Kit
- Teseq ISO 7637-3 ICC for NSG 5500 System
- Used for Injection of Pulse 2A
- Includes CIP 9136A, PCJ 9201, & INA 5580
EM Test AMP 200N2 - Rent LF Signal & Amplifier DC - 500 KHz
- Output Max. 160 V p-p, 50 V rms
- Output Current Max. 18 A rms
- Automatic Closed Loop Test Procedures
Conducted Transient Emissions Set ISO 7637-2 EM Test
- Electronic Switch, Artificial Network, & RS-Box
- BS 200N100 Electronic switch, 60V DC/100A
- AN 200N100 1,000V DC, 250V AC (up to 1kHz)