IEC 61000-4-2 ESD Simulators

Get fast delivery of ISO 17025 calibrated simulators/guns from Teseq, EM Test, Haefely, and many others. Our inventory also includes accessories and equipment used in the test setup including ESD grounding cable, VCP, as well as complete setups.

Related:
Showing 1 - 6 of 6 products out of 18
Quick Access
Return Instructions

Rental Terms


  1. TSI retains title of all equipment. Customers are precluded from altering, assigning, modifying or encumbering the equipment in any way.
  2. Equipment is shipped F.O.B. shipping point and must be returned prepaid and insured to TSI per shipping instructions included with the equipment. Customers are responsible for all taxes and duties related to the lease of the equipment.
  3. The lease is non-cancelable for its initial term and may not be renewed without permission from TSI. If it is renewed, the customer is responsible for all lease charges accrued whether or not the customer has issued additional purchase orders.
  4. In the event that the equipment is non-functional, lease charges are abated from the date that notification is given to TSI, until a replacement unit is furnished to the customer. Notification of a non-functional unit must be given within 72 hours of delivery or the customer will be responsible rental charges accrued between delivery date and the date they notified TSI of a problem. Notification of missing accessories must be given within 72 hours of delivery or the customer will be responsible for the return of all accessories listed on the packing list.
  5. The customer shall bear all risks of loss or damage to the equipment from the time of shipment until TSI receives the equipment in good working order, unless notification is given per sec. 5.
  6. The customer agrees that TSI has not made any representation of warranty, expressed or implied (except as stated in the document) on the equipment and the responsibility for equipment selection, suitability and fitness of use for a particular purpose lies solely with the customer.
  7. The customer will hold TSI harmless from all claims and expenses resulting from the selection, delivery, use and/or possession of any equipment obtained from or through TSI.
  8. In the event of default by the customer of any of the above terms and conditions, TSI shall be entitled to the immediate possession of this equipment.
  9. The customer agrees that the terms and conditions listed here shall supersede any conflicting terms in, or attached to, the purchase order.
  10. This agreement shall be interpreted according to the laws of the State of Illinois. The customer shall pay to TSI all costs and expenses, including reasonable attorneys’ fees, incurred by TSI in exercising any of its rights or remedies with regard to the rental or enforcement of any of these terms and conditions.
FAQs
ESD Test Setup - IEC 61000-4-2 Side Front ESD Test Setup - IEC 61000-4-2 Side
ESD Test Setup - Buy & Rent IEC 61000-4-2 Table Top
  • GCP, HCP, VCP, & Cables w/ Resistors 
  • For Full IEC 61000-4-2 Table Top Setup
  • Can be Purchased New/Used or Rented
In Stock
MD 102A & Cable MD 102A, Case, & Cable - Side
Teseq MD 102A - ESD Target for Waveform Verification
  • Current target as per IEC/EN 61000-4-2
  • Includes Target, Attenuator & Cable
  • Target for Precise ESD Pulse Measurements
EM Test EAS 30 Front EM Test EAS 30 Connectors
EM Test EAS 30 - ESD Grounding/Bleeder Cable & Resistor
  • Bleed Off Cable Including HV Resistors 2X470 kΩ
  • Can be Purchased in .8 or 2 Meter Length
  • Max ESD Test Voltage 30 kV
In Stock
Teseq INA 102A
Teseq INA 102A - 50 Ohm Calibration Adapter MD 102A/103
  • 50 Ohms as Required by IEC 61000-4-2
  • Designed for Calibration of MD 102A/103
  • ISO 17025 Calibration Available
EM Test VCP - Vertical Coupling Plane IEC 61000-4-2 EM Test VCP - Vertical Coupling Plane IEC 61000-4-2
EM Test VCP - Vertical Coupling Plane IEC 61000-4-2
  • Vertical Coupling Plane for IEC 61000-4-2
  • Includes one Bleed Off Cable with Resistors
  • Wood Stand with Tightening Clamp Included 
ESD Static Dissipation Brush - Front Side ESD Static Dissipation Brush - lifted
ESD Static Dissipation Brush - IEC 61000-4-2 Charge Removal
  • Carbon Fiber Brush Designed for Charge Removal
  • Meets IEC 61000-4-2:2009 Requirements
  • 2 x 470 kΩ 10 kV Dissipation Resistors 
In Stock