ISO 7637 Test Equipment Rentals - Automotive EMC Test Equipment
- Rent Single & Multiple System Solutions
- Get both Teseq and EM Test Equipment
- Rental Systems Include ISO 17025 & Laptops
- Many Manufacturer & OEM Pulse Equipment
- 100Amp Teseq & 50Amp EM Test Capabilities
- Updated Systems & Software - Newest Versions
- Rent up to 100 Amp DUT EFT Systems
- Variety of Test Accessories & Verification
- Rent Individual Pulse & Complete Systems
- Equipment - ISO 17025 & Laptops with Software
- Preferred Rental Partner Ametek CTS
- Comparable NSG 5500 & PA5840 System Available
Load Dump Equipment
ISO 16750-2 Test Solutions
EFT/Microburst Generators
Automotive Fast Transients
DC Battery Simulators
Voltage Drop Generator
All Transient System
Automotive Test Systems
Automotive ESD Equipmet
ISO 10605 Compliant
- Includes NSG 5500, PA 5840, & CDN 400
- ISO 7637-2 & ISO 7637-3 Tests
- Battery Simulators up to 60 V 100 A
- Generators Clipped Load Dump Pulses
- Tests to ISO 7637-2 & ISO 16750-2 Load Dump
- Built-in CDN Max 80 Volts 30 Amps
- Micropulse Generator for ISO, JASO, & SAE
- ISO 7637-2 Pulses 1, 2a, 3a, & 3b
- Built-in CDN Max 80 Volts 50 Amps
- Micropulse Generator for ISO, JASO, & SAE
- ISO 7637-2 Pulses 1, 2a, 3a, & 3b
- Built-in CDN Max 80 Volts 100 Amps
- Pulses 4 and 2b (ISO 7637-2/ISO 16750-2)
- Maximum 60 Voltage 30 Amps
- Voltage Drop Simulator with Low Output Impedance
- Pulses 4 and 2b (ISO 7637-2/ISO 16750-2)
- Maximum 60 Voltage 15 Amps
- Voltage Drop Simulator with Low Output Impedance
- Calibration Kit Designed for EM Test Systems
- Compliant to IEC 61000-4-4 & ISO 7637, Annex D
- Includes KW 50 (50Ω) & KW1000 (1kΩ)
- Test System for ISO 7637-2/3 Requirements
- Battery Simulators Available up to 100 Amps
- Pre-programmed International & OEM Tests
- -60 to +60 Volts 50 Amps Continuous
- Pulses 4 and 2b (ISO 7637-2/ISO 16750-2)
- Extended Range 80 Volts 40 Amps
- 2-channel Arbitrary Waveform Generator
- Dual-Processor-Technology, 500kS/s sample rate
- Library of Standard Test Routines
- Frequency Range 4 kHz - 400 MHz
- Compliant to IEC, ISO, & MIL-STD Tests
- High power handling (up to 1 kW)
- ISO 7637-3 & OEM Compliant Solution
- Accepts Cables up to 40mm Diameter
- Solution for Testing Shielded Signal Lines
- -15 to +60 Volts 25 Amps Continuous
- High Bandwidth up to 150 kHz
- 75 Amps Inrush Current Capability
- Includes all Required Load Resistor Values
- Resistors with very low inductance
- Highly accurate resistors (+/-1%)
- 10 Ohm & 100 Ohm Power Calibration Loads
- 1 Ohm & 1000 Ohm Data Line Calibration Loads
- Designed for up to 48 Volt Battery Lines
- Compliant Pulses to FMC1278 & EMC-CS-2009.1
- Pulses CI 220: A1, A2-1, A2-2, C-1 and C-2
- Pulses RI 130: A2-1, A2-2 with Coupling Test Fixture
Overview
Renting test equipment for this standard allows for the same quality equipment at a fraction of the price of purchasing new. This automotive that defines testing parameters for electrical disturbances from conduction and coupling including that of electrical transient conduction along supply lines of vehicles. This automotive EMC testing standards consists of five components including ISO 7637-2. This standard is available for purchase at the ISO Website. It sets testing parameters for temperature, supply voltage, setup, measurement, test equipment, and many other factors. The ISO 7637 series of tests include both immunity and emissions components of EMC. testing. This standard specifies shapes and parameters for pulses and provides details about required electrical components. 
ISO 7637 can be tested to with Automotive EMC Immunity Test Equipment and provides performance status classifications for immunity. The classification status is based upon the pulse severity level, minimum number of pluses, and burst cycle. The rating table based on these factors can be different for each kind of pulse, and for both 12 V and 24 V systems. ISO 7637-2 test equipment provides necessary information on test pulses 1, 2a, 2b, 3a, 3b and for 4, 5a, and 5b refers to ISO 16750-2 and ISO 21848. This EMC based standard also describes bench tests for both the injection and measurement of transients. Our test equipment rentals provide capabilities to test to many manufacturer standards that are based off this standard.
Setup
The setup for this standard places special emphasis on the location of device under test (DUT), power supply lines, and location of load simulator. The DUT must be placed non-conductive support with a thickness of 50mm (+/-10%). For test pulses 3a & 3b it is necessary that the test pulse generator and DUT will be laid in a parallel line on a on-conductive support with a thickness of 50mm (+/-10%) with a length of (500 ± 100) mm.
Test Equipment
