ISO 7637 Test Equipment Rentals - Automotive EMC Test Equipment
- Rent Single & Multiple System Solutions
- Get both Teseq and EM Test Equipment
- Rental Systems Include ISO 17025 & Laptops
- Many Manufacturer & OEM Pulse Equipment
- 100Amp Teseq & 50Amp EM Test Capabilities
- Updated Systems & Software - Newest Versions
- Rent up to 100 Amp DUT EFT Systems
- Variety of Test Accessories & Verification
- Rent Individual Pulse & Complete Systems
- Equipment - ISO 17025 & Laptops with Software
- Preferred Rental Partner Ametek CTS
- Comparable NSG 5500 & PA5840 System Available
Load Dump Equipment
ISO 16750-2 Test Solutions
EFT/Microburst Generators
Automotive Fast Transients
DC Battery Simulators
Voltage Drop Generator
All Transient System
Automotive Test Systems
Automotive ESD Equipmet
ISO 10605 Compliant
- Switch for Power Lines 100 A and Data Lines 2 A
- Fast Switch with Rise/Fall Times of 200ns
- Pulses E10 and E13 of the LV 124/LV 148
- Provides LV124 E-01 to E-15 Pulses
- DUT Capabilities up to 100 Amps
- Includes Software & Verification Kits
- Many pulses of LV124/Other OEMs (100A)
- Includes - Accessory Kit, Autowave & PA 5840
- Rent PFM200N100 for Additional OEM Pulses
- Teseq ISO 7637-3 ICC for UCS 200N Series
- Used for Injection of Pulse 2A
- Includes CIP 9136A, PCJ 9201, & MN-CIP9136
- Max 1000 Volts 100 Amps DC (150 Amp Peak)
- ISO 7637-2, ISO 11452-4, & CISPR 25 Compliant
- Switch for Selecting Testing Requirements
- Teseq ISO 7637-3 ICC for NSG 5500 System
- Used for Injection of Pulse 2A
- Includes CIP 9136A, PCJ 9201, & INA 5580
- Output Max. 160 V p-p, 50 V rms
- Output Current Max. 18 A rms
- Automatic Closed Loop Test Procedures
- Electronic Switch, Artificial Network, & RS-Box
- BS 200N100 Electronic switch, 60V DC/100A
- AN 200N100 1,000V DC, 250V AC (up to 1kHz)
- Frequency response 10 Hz to 500 kHz
- Audio power up to 3 x 200 W
- Turns ratio 2:1 step down
- Max 1000 V/150 A DC or 500 V/150 A AC
- HV Compliant to ISO 7637-4 & CISPR 25
- Jumpers Provide LISN Path Configuration
- Max 1000 V/200 A DC or 700 V/200 A AC
- Includes HVSE 8600 Shielded Enclosure
- 5uH LISN in Accordance with CISPR 25
- Designed for use with Teseq HV-AN 150s
- Rugged Design using Stainless Steel
- Compliant to HV CISPR 12/25 & ISO 7637-4
- Designed for use with NNHV 8123-200
- Compliant to HV CISPR 25 & BMW GS 95025-1
- Rented with set of NNHV 8123-200 LISNs
- Electronic Switch Accordance with ISO 7637 Part 2
- Rented with EM Test Transient Emissions Set
- Max 60 Volts & 100 Amps Cont. (400A @ 200ms)
- Impedance 50 µH || 50 Ω
- Frequency Range 150 kHz – 30 MHz
- Maximum: 200 Amps 700 Volts AC
- 4-channel Arbitrary Waveform Generator
- 2-channel Transient Waveform Recorder
- Simultaneous Recording/Generation
Overview
Renting test equipment for this standard allows for the same quality equipment at a fraction of the price of purchasing new. This automotive that defines testing parameters for electrical disturbances from conduction and coupling including that of electrical transient conduction along supply lines of vehicles. This automotive EMC testing standards consists of five components including ISO 7637-2. This standard is available for purchase at the ISO Website. It sets testing parameters for temperature, supply voltage, setup, measurement, test equipment, and many other factors. The ISO 7637 series of tests include both immunity and emissions components of EMC. testing. This standard specifies shapes and parameters for pulses and provides details about required electrical components. 
ISO 7637 can be tested to with Automotive EMC Immunity Test Equipment and provides performance status classifications for immunity. The classification status is based upon the pulse severity level, minimum number of pluses, and burst cycle. The rating table based on these factors can be different for each kind of pulse, and for both 12 V and 24 V systems. ISO 7637-2 test equipment provides necessary information on test pulses 1, 2a, 2b, 3a, 3b and for 4, 5a, and 5b refers to ISO 16750-2 and ISO 21848. This EMC based standard also describes bench tests for both the injection and measurement of transients. Our test equipment rentals provide capabilities to test to many manufacturer standards that are based off this standard.
Setup
The setup for this standard places special emphasis on the location of device under test (DUT), power supply lines, and location of load simulator. The DUT must be placed non-conductive support with a thickness of 50mm (+/-10%). For test pulses 3a & 3b it is necessary that the test pulse generator and DUT will be laid in a parallel line on a on-conductive support with a thickness of 50mm (+/-10%) with a length of (500 ± 100) mm.
Test Equipment
