Conducted Immunity Test Equipment Rentals
- Construction as per IEC 61000-4-4 Ed.3
- EFT/Burst Testing of Signal- and Datalines
- Permissible Burst Voltage 7 kV
- Construction as per IEC 61000-4-4 Ed.3
- EFT/Burst testing of signal and data lines
- For cable diameter from 4 – 40 mm
- Coupler for Surge, EFT, & Ringwave Pulses
- Max 125 Amps 690 V AC or 1,000 V DC
- Transient Generator Mounted in Rack
- 10 kHz - 400 MHz 100 Watt RF Immunity System
- Built-in Signal Generator & Spectrum Analyzer
- Preprogrammed Test Routines/Sequences
- 16 kV Air & 10 kV Contact Discharge (10 V Steps)
- Light Weight Ergonomic Design
- 150 pF/ 330 Ohm Network Installed
- 16 kV Air & 10 kV Contact Discharge
- 150 pF/ 300 Ω Discharge Module
- Used with ESD3000 ESD Simulator
- 30 kV 150 pF/330 Ω Discharge Network
- Used with ESD3000 ESD Simulator
- Requires RM32 Relay Module
- 30 kV 300 pF/2 kΩ Discharge Network
- Used with ESD3000 ESD Simulator
- Requires RM32 Relay Module
Need help selecting the right immunity equipment?
What is Conducted Immunity?
Conducted immunity is a devices ability to withstand noise or interference transmitted via direct physical connection, commonly through power or data lines.
This large category of EMC test encompases a wide variety of requirements, the most common include, electrostatic discharge (ESD), combination wave surges, electrical fast transients (EFT), conucted RF testing, as well as a many others. Tests are typically conducted with the equipment under test (EUT) power on and any deviations from normal operation are noted and compared to the underlying standard to determine if the EUT passed testing.
ESD Testing & Equipment
ESD simulators or ESD guns provide the necessary waveforms to meet a variety of standards as well as ensure products are robust enough operate in the intended environemnt. As the US distributor and preferred rental partner of Ametek CTS, we stock many of the most popular Teseq and EM Test simulators allowing us to provide immediate delivery on many test sysetms.
Simulators are commonly define by:
- Test Level: 16kV & 30kV
- Resistance Capacitance Modules/Networks
- Compliance to Particular Standard(s)
- Unique Equipment Capabilities
EFT & Surge Transient Generators
General Testing Information
Immunity is the impact that electromagnetic energy has on the function of an electronic device. The International Electronical Commission (IEC) Electromagnetic Compatibility (EMC) testing standards are most comprehensive and widely used for EMC testing. These standards all fall under the basic publication of IEC 61000, which is general guidelines for EMC. The phenomena which these sets of standards are based off of include Combination Wave/Surge, Ring Wave, Burst/Electronic Fast Transients (EFT), and Dips and many others.
Conducted RF Test Equipment
Conducted RF test systems are a combination of several pieces of equipment including RF amplifier, signal genetor, power meter/spectrum analyzer, and software. These systems are designed to be generate a signal at a modulated level (will very by standard) at a given level over the associated frequency range.
Rental compliant systems to:
- ISO 11452-4
- Ford FMC1278
- MIL-STD-461 CS114
- RTCA DO-160G CS Test
Common Standards/Requirements
IEC Standards
- IEC 61000-4-2 - Electrostatic Discharge (ESD)
- IEC 61000-4-4 - Electronic Fast Transients(EFT)/Burst
- IEC 61000-4-5 - Surges (Combination Wave)
- IEC 61000-4-6 - Conducted RF Distrubances
- IEC 61000-4-11 - Dips, Interruptions, & Variations
- IEC 61000-4-12 - Ringwave Pulse
ANSI/IEEE Standards
Teseq NSG 4070C - Rent Conducted RF Immunity Test System
ESD Simulators - Rent & Buy Systems
Rent and buy ESD simulators from US distributor for Teseq and EM Test ESD simulators and test accessories in the United States. Get fast deliveries on ISO 17025 calibrated equipment, including test solutions for commercial, automotive, and military applications.
- 16.5 kV Air & 9 kV Contact Discharge (100 V Steps)
- Rechargeable Battery Powered ESD Simulator
- Built-in 150 pF/ 330 Ohm Network
- 16 kV Air Discharge & 10 kV Contact-discharge (100 V Steps)
- Rechargeable Battery Powered ESD Simulator
- Includes DM1 150pF / 330Ω Network for IEC 61000-4-2 Testing
- 30 kV Air & Contact Discharge (100V Steps)
- Rechargeable Battery Powered ESD Simulator
- Charge Removal Feature Capabilities
- 16 kV Air Discharge & Contact Discharge (100 V Steps)
- Simple Easy to Navigate Touch Screen
- Predefined Test Routines According to Standards
- 30 kV Air & Contact Discharge (100V Steps)
- Rechargeable Battery Powered ESD Simulator
- Includes 150 pF/ 330 Ohm Network (INA 4380)
- 16 kV Air & 10 kV Contact Discharge (10 V Steps)
- Light Weight Ergonomic Design
- 150 pF/ 330 Ohm Network Installed
- 30V Air & Contact Discharge (100V Steps)
- Color Touch Panel Control with Activity Log
- Includes 150 pF/ 330 Ohm Network (INA 4380)
- 15 kV Air Discharge & 8 kV Contact Discharge (10V Steps)
- Rugged, Portable, and Self Contained ESD Simulator
- Meets Requirements of IEC 61000-4-2 & ANSI C63.16
Coupling Decoupling Networks
Rent both power and data line CDNs designed for meeting a variety of EUT/DUT immunity testing requirements. We offer both manual and automatic power mains CDNs up to 125 Amps meeting the newest requirements of IEC 61000-4-5.
- Coupler for Surge, EFT, & Ringwave Pulses
- Max 125 Amps 690 V AC or 1,000 V DC
- Transient Generator Mounted in Rack
- Coupler for Surge to IEC 61000-4-5
- Max 100 Amps 690 V AC or 620 V DC
- Manual Coupler for NSG 3060 or NSG 3040
- Designed for Burst to IEC 61000-4-4
- Max 100 Amps 690 V AC or 1,000 V DC
- Handles up to 8.8 kV EFT/Burst Pulses
- Coupler for Surge, EFT, & Ringwave Pulses
- Max 480 Volts 32 Amps AC
- Automatic Coupler for NX5/NX7 Systems
- Coupler for Surge, EFT, & Ringwave Pulses
- Maximum 480 Volts 32 Amps AC/DC
- Automatic Coupler for Axos5/8 Systems
- CDN for up to 8 wire unshielded twisted pair (UTP)
- Max Surge Voltage 2 kV Current 50 Amps
- Coupling to 1, 2 or 4 pairs
- Coupler for Damped Oscillatory Pulses
- Maximum 480 Volts 25 Amps AC
- Rented with MIG-OS-OS1 Generator
- Coupler for Surge, EFT, & Ringwave Pulses
- Maximum 270 Volts 16 Amps AC/DC
- Rented with Teseq NSG 3060 Test System
- Coupler for Surge, EFT, & Ringwave Pulses
- Maximum 480 Volts 32 Amps AC/DC
- Automatic Coupler for NSG 3060/NSG 3040
- CDN for Shielded & Unshielded Data Lines
- Maximum 3 kV Surge & 4 kV EFT/Burst
- Compatible to PoE and PoE+ requirements
- Construction as per IEC 61000-4-4 Ed.3
- EFT/Burst Testing of Signal- and Datalines
- Permissible Burst Voltage 7 kV
- Construction as per IEC 61000-4-4 Ed.3
- EFT/Burst testing of signal and data lines
- For cable diameter from 4 – 40 mm
- IEC 61000-4-4 & IEC 61000-4-18 Compliant
- Designed for Coupling to I/O Lines
- Useable for Damped Oscillatory Wave Testing
- Coupler for Surge to IEC 61000-4-5
- Max 100 Amps 690 V AC or 1,000 V DC
- Manual Coupler for NX5/NX7 Systems
- Coupler for EFT/Burst to IEC 61000-4-4
- Max 100 Amps 690 V AC or 1,000 V DC
- Manual Coupler for NX5/NX7 Systems
- Construction as per IEC 61000-4-4 Ed.3
- EFT/Burst Testing of Signal- and Datalines
- Permissible Burst Voltage 7 kV
- Construction as per IEC 61000-4-4 Ed.3
- EFT/Burst testing of signal and data lines
- For cable diameter from 4 – 40 mm
- Coupler for Surge, EFT, & Ringwave Pulses
- Max 125 Amps 690 V AC or 1,000 V DC
- Transient Generator Mounted in Rack
- 10 kHz - 400 MHz 100 Watt RF Immunity System
- Built-in Signal Generator & Spectrum Analyzer
- Preprogrammed Test Routines/Sequences
- 16 kV Air & 10 kV Contact Discharge (10 V Steps)
- Light Weight Ergonomic Design
- 150 pF/ 330 Ohm Network Installed
- 16 kV Air & 10 kV Contact Discharge
- 150 pF/ 300 Ω Discharge Module
- Used with ESD3000 ESD Simulator
- 30 kV 150 pF/330 Ω Discharge Network
- Used with ESD3000 ESD Simulator
- Requires RM32 Relay Module
- 30 kV 300 pF/2 kΩ Discharge Network
- Used with ESD3000 ESD Simulator
- Requires RM32 Relay Module
- 30 kV 150 pF/2 kΩ Discharge Network
- Used with ESD3000 ESD Simulator
- Requires RM32 Relay Module
- 30 kV 330 pF/330 kΩ Discharge Network
- Used with ESD3000 ESD Simulator
- Requires RM32 Relay Module
- 16 kV Air & 10 kV Contact Discharge
- 100 pF/ 1,500 kΩ Discharge Module
- Used with ESD3000 ESD Simulator
- 30V Air & Contact Discharge (100V Steps)
- Color Touch Panel Control with Activity Log
- Auto Variation Includes 3 Automotive Networks
- GCP, HCP, VCP, & Cables w/ Resistors
- For Full IEC 61000-4-2 Table Top Setup
- Can be Purchased New/Used or Rented
- 30 kV Air & Contact Discharge (100V Steps)
- Rechargeable Battery Powered ESD Simulator
- Includes 150 pF/ 330 Ohm Network (INA 4380)
- 30 kV Air & Contact Discharge (100V Steps)
- Rechargeable Battery Powered ESD Simulator
- Auto Variation Includes 3 Automotive Networks
- 30V Air & Contact Discharge (100V Steps)
- Rechargeable Battery Powered ESD Simulator
- Includes 150 pF/ 330 Ohm Network (INA 4380)
What is Conducted Immunity?
Conducted immunity is a devices ability to withstand noise or interference transmitted via direct physical connection, commonly through power or data lines.
This large category of EMC test encompases a wide variety of requirements, the most common include, electrostatic discharge (ESD), combination wave surges, electrical fast transients (EFT), conucted RF testing, as well as a many others. Tests are typically conducted with the equipment under test (EUT) power on and any deviations from normal operation are noted and compared to the underlying standard to determine if the EUT passed testing.
ESD Testing & Equipment
ESD simulators or ESD guns provide the necessary waveforms to meet a variety of standards as well as ensure products are robust enough operate in the intended environemnt. As the US distributor and preferred rental partner of Ametek CTS, we stock many of the most popular Teseq and EM Test simulators allowing us to provide immediate delivery on many test sysetms.
Simulators are commonly define by:
- Test Level: 16kV & 30kV
- Resistance Capacitance Modules/Networks
- Compliance to Particular Standard(s)
- Unique Equipment Capabilities
EFT & Surge Transient Generators
General Testing Information
Immunity is the impact that electromagnetic energy has on the function of an electronic device. The International Electronical Commission (IEC) Electromagnetic Compatibility (EMC) testing standards are most comprehensive and widely used for EMC testing. These standards all fall under the basic publication of IEC 61000, which is general guidelines for EMC. The phenomena which these sets of standards are based off of include Combination Wave/Surge, Ring Wave, Burst/Electronic Fast Transients (EFT), and Dips and many others.
Conducted RF Test Equipment
Conducted RF test systems are a combination of several pieces of equipment including RF amplifier, signal genetor, power meter/spectrum analyzer, and software. These systems are designed to be generate a signal at a modulated level (will very by standard) at a given level over the associated frequency range.
Rental compliant systems to:
- ISO 11452-4
- Ford FMC1278
- MIL-STD-461 CS114
- RTCA DO-160G CS Test
Common Standards/Requirements
IEC Standards
- IEC 61000-4-2 - Electrostatic Discharge (ESD)
- IEC 61000-4-4 - Electronic Fast Transients(EFT)/Burst
- IEC 61000-4-5 - Surges (Combination Wave)
- IEC 61000-4-6 - Conducted RF Distrubances
- IEC 61000-4-11 - Dips, Interruptions, & Variations
- IEC 61000-4-12 - Ringwave Pulse
ANSI/IEEE Standards
