EM Test NX5 bsp-1-300-32
Included Accessories
Can't find something? Contact UsRelated Equipment
Description
The compact Next Generation NX5 is the most versatile tester to address transient and power fail requirements for both international and commercial standards.
Featuring an easy-to-use color touch screen, the NX5 provides an economical solution for pre-compliance immunity testing as well as full-compliance testing and CE Marking. Its internal single-phase Coupling/Decoupling Network (CDN) can be extended for testing three-phase EUTs by means of an automatically controlled external CDN up to 200 A per phase. EM TEST supplies a large range of accessories for various applications such as magnetic field tests and more.
Benefits
The compact NX5 is a standalone generator which includes everything necessary to perform fully compliant tests. With separate power mains supply inputs, it allows the utilization of different EUT supply voltages for maximum flexibility.
The NX5 can be operated manually from the intuitive front touch screen or remotely via its built-in Ethernet, USB or optical interface. Failure inputs allow control of an ongoing test sequence based on the state of the EUT. Monitoring outputs (BNC) offer easy signal verification and measurements. For enhanced safety requirements, features like interlock and a warning lamp are available.
NX5 is the first generator that recognizes the connected EUT power configuration. Only coupling selections to active lines are enabled. Non existing lines will be disabled from the menu settings. Pre-programmed routines with common Test Standards allow maximum user convenience. Quick Start Test routines where parameters can be changed during susceptibility level evaluation are also available.
- General Data
- Interfaces:
- Serial interface
- 2 x USB A for memory stick,
1 x USB B for service only,
Opto - Link to USB for remote - Lan
- Ethernet for remote
- Analog output
- 0 - 10 VDC to control an external transformer
- Sys.link
- 26 pin high density connector to control an external coupling network
- Fail inputs
- EUT monitoring via input (one each)
EUT Monitor 1
EUT Monitor 2 - Ext. Trigger
- BNC Ext. Trigger IN pos slope 5 V
- Ext. Sync Input
- Differential input,
50 V - 690 VAC,
2 x 4 mm MC Safety connectors - Dimensions and Weight:
- 16 A models
- 19"/3 HU, 500 mm deep, approx. 21.8 kg
- 32 A models
- 19"/6 HU, 500 mm deep, approx. 40 kg
- Environment:
- Temperature
- 10 C to 35 C
- Humidity
- 30 % to 75 %, non condensing
- Atmospheric pressure
- 86 kPa (860 mbar) to 106 kPa (1,060 mbar)
- Mains:
- Supply voltage
- 85 V - 264 V
- Frequency
- 50/60 Hz
- Power
- approx. 75 W
- Fuses
- 115 V: 2 x 4 A slow blow, 230 V: 2 x 2 A slow blow
- Safety:
- Safety standard
- IEC/EN 61010
- Security circuit
- Control input (24 VDC)
- Warning lamp
- Floating contact (max. 60 V/2 A)
- Accessories Included:
- Mains supply
- Plug depends on the country of use
- EUT supply
- Plug depends on the country of use
- EUT adapter
- Socket depends on the country of use
- Operation manual
- Calibration certificate
- iec.control remote control software
- Specifications:
- Burst Module
- As per IEC/EN 61000-4-4 and EN 61000-6-1, -6-2
- Test voltage
- 200 V - 5,500 V +/- 10%; 100 V - 2,750 V +/- 10% into 50 ohm
- Pulse shape
- 5/50 ns into 50 ohm and 1,000 ohm
- Rise time tr
- 5 ns +/-30% into 50 ohm;
5 ns+/ 30% into 1,000 ohm - Pulse width td
- 50 ns +/-30% into 50 ohm;
50 ns -15/+100 ns into 1,000 ohm - Source impedance
- 50 ohm
- Polarity
- Positive/negative
- Trigger Circuit:
- Trigger of bursts
- Automatic, manual, external
- Synchronization
- 0 - 360 Degree, resolution 1 Degree (16 - 500 Hz)
- Burst duration (td)
- td = 0.10 ms - 9,999 ms
- Repetition rate (tr)
- tr = 10 ms - 9,999 ms
- Spike frequency
- f = 1 Hz - 1,000 kHz
- Test duration
- T = 0:01 min - 99:59 min
T > 99:59 min --> endless - Outputs:
- Direct
- Via 50 ohm coaxial connector
- Coupling mode
- L, N, PE; all combinations
- EUT supply
- AC: 300 V / 400 V, 50/60 Hz
DC: 300 V / 400 V,
Current: 16 A / 32 A - CRO trigger
- 5 V trigger signal for oscilloscope
- Test Routines:
- Quick Start
- On-line adjustable parameters, easy-to-use
- Standard Test routines
- As per IEC/EN 61000-4-4, Levels 1 - 4
As per IEC/EN 61000-6-1, -6-2
As per ECE R-10 Rev5 - Extended Test routines
- Change voltage after T,
Frequency sweep within one burst,
Frequency sweep with constant number of pulses,
Frequency sweep with constant burst duration,
Synchronous burst release,
Random burst release - Combination Wave Surge:
- Surge Module
- As per IEC/EN 61000-4-5 and IEC/EN 61000-6-1, -6-2
- Voltage (o.c.)
- 160 V - 5,000 V +/- 10%
- Pulse front time
- 1.2 us +/- 30%
- Pulse duration
- 50 us +/- 20%
- Current (s.c.)
- Max. 2,500 A +/- 10%
- Pulse front time
- 8 us +/- 20%
- Pulse duration
- 20 us +/- 20%
- Polarity
- Positive/negative/alternating
- Trigger Circuit:
- Release of pulses
- Automatic, manual, external
- Synchronization
- 0 - 360 degrees, resolution 1 degree
- Repetition rate
- max. 1 Hz (1 s - 9,999 s)
- Event counter
- 1 - 99,999, selectable
- Outputs:
- Direct
- Via HV connectors for external coupling networks
- Coupling mode
- Line to line
Line(s) to ground - EUT supply
- AC: 300 V / 400 V,
50/60 Hz DC: 300 V / 400 V,
Current: 16 A / 32 A - CRO trigger
- 5 V trigger signal for oscilloscope
- Measurements
- CRO U-monitor
- 10 Vp at 5,000 V
- CRO I-monitor
- 10 Vp at 2,500 A
- Peak voltage
- 5,000 V in the touch display
- Peak current
- 2,500 A in the touch display
- Overcurrent protection
- Breaks the Surge test when the surge current is over the limit,
Limiter for differential mode,
Limiter for common mode - EUT current
- RMS current, Range 50 A, < +/-5%
- EUT overcurrent protection
- Breaks the test when the EUT current is over the limit,
- Test Routines:
- Quick Start
- One-line adjustable parameters, easy-to-use
- Standard Test routines
- As per IEC/EN 61000-4-5,
As per IEC/EN 61000-6-1,
As per IEC/EN 61000-6-2,
Manual Standard Test routine - Extended Test routines
- Voltage iteration after n pulses,
Angle iteration stepwise,
Phase angle random iteration,
Change coupling after n pulses,
Change phase angle after n pulses - Pulsed Magnetic Field
- as per IEC/EN 61000-4-9
Test levels 100, 300 and 1,000A/m
Test level continuously adjustable under Quick Start - Power Fail:
- As per
- IEC/EN 61000-4-11,
IEC/EN 61000-4-29
and IEC/EN 61000-6-1, -6-2 - Channel PF1/PF2
- AC voltage: max. 300 V / 400 V
AC current: max. 16 A / 32 A
DC voltage: max. 300 V / 400 V
DC current: max. 16 A / 32 A - Frequency
- 16 Hz - 500 Hz and DC
- Switching time
- > 1 us < 5 us into a 100 ohm resistive load (SVP 100)
- Inrush current
- > 500 A
- Protection
- Both channels are protected against short-circuit conditions.
- Trigger Circuit:
- Trigger of events
- Automatic, manual, external
- Synchronization
- 0 - 360 degrees, resolution 1 degree (16 - 500 Hz)
- Repetition rate
- 10 ms - 9,999 s
- Event duration
- 10 us - 99.999 s
- Event counter
- 1 - 99,999, selectable
- Outputs:
- EUT terminals
- L, N and PE
- CRO trigger
- 5 V trigger signal for oscilloscope
- Measurements:
- EUT voltage (rms)
- In the touch screen
- EUT current (rms)
- In the touch screen
- MON V
- Measurement of the EUT voltage, built-in divider:
300 V: 42,5:1, 10 V =425 Vpk,
400 V: 56.6:1, 10 V =566 Vpk - MON I
- Measurement of the EUT current,
16 A: 7 A/V; 10 V =70 Apk,
32 A: 10 A/V; 10 V =100 Apk - Test Routines:
- Quick Start
- On-line adjustable parameters, easy-to-use
- Standard Test routines
- As per IEC/EN 61000-4-11 for AC supplies
As per IEC/EN 61000-4-29 for DC supplies
As per EN 61000-6-1, -6-2 Manual Standard Test routine - Extended Test routines
- Voltage variation, control of an external variac,
Phase angle iteration, Reduced time iteration,
Angle inverse mode, Random by step and list Inverse mode - 50/60 Hz magnetic field
- As per IEC/EN 61000-4-8 Test levels 1, 3, 10 and 30 A/m with external current transformer MC 2630, Test levels 100, 300 and 1,000 A/m with external current transformer MC 26100
info@transientspecialists.com