Description
Overview
The Teseq Profline2105 by Teseq has a stable and programmable 5KVA power supply and line conditioner (Cal Inst 5000ix) used for measuring single phase harmonics (EN/IEC 61000-3-2) and flicker (EN/IEC 61000-3-3) testing. The NSG1007 power supply is included in the Profline2105 rental. An A2LA accredited calibration is included in the EMC rental equipment price.
This Harmonics and Flicker Emissions Tester has a fully programmable AC power source with arbitrary waveform generator capable of being used in stand-alone mode in various applications for IEC 61000-4-X at pre or full-compliance. The measurement of flicker requires a fixed, stable source impedance the Profline system provides a precision power source to accurately simulate this impedance by careful control of the relationship between voltage and current. This IEC 61000-3-3 rental solution eliminates the need for a costly physical impedance.
The Profline 2105 is a reliable solution for testing to standards EN/IEC 61000-3-2, EN/IEC 61000-3-3, EN/IEC 61000-4-11, EN/IEC 61000-4-13, and EN/IEC 61000-4-14. Measurements are made using precision, no burden, active hall-effect current transformers connected via a dedicated cable to a multichannel fast Data Acquisition Card (DAQ) fitted inside a PC. One voltage and three current measuring channels are used to make simultaneous measurement of both current and voltage.
ProfLine - Data Sheet Teseq - Harmonics & Flicker NSG1007 - Data SheetSpecifications
Common Standards |
EN/IEC 61000-3-2, EN/IEC 61000-3-3, EN/IEC 61000-4-11, EN/IEC 61000-4-13, & EN/IEC 61000-4-14 |
Power Source |
5kVA – single phase 0-270V, 18.5A |
Synthesized impedance |
Per IEC 725 |
Data Acquisition |
4 channels |
Sampling Rate |
>200kHz (4000 times fundamental) per channel |
Harmonics Analysis |
|
Range |
Fundamental to 40th harmonic |
Fundamental |
±0.05% FS ±0.05% / kHz |
Harmonics |
±0.1% ±0.1% / kHz |
Measurement Window |
Real time FFT of 200msec. |
Smoothing |
1.5 sec. |
Flicker Analysis |
|
Range |
0.4- 5 Pst |
Accuracy |
3% |
Resolution |
0.01 |
Integration Time |
10 mins |
Plt |
0.4 - 5 |
dmax |
0.1 – 100% |
dc |
0.1 – 100% |
dt |
0.1 – 100% |
dt over 3.3% |
10 – 5000 ms |
Other Immunity Testing |
|
IEC 61000-4-11 |
AC voltage dips, interrupts and variations with optional EOS1 |
IEC 61000-4-13 |
Immunity to harmonics and interharmonics |
IEC 61000-4-14 |
Immunity to voltage fluctuations |
IEC 61000-4-17 |
Ripple on DC input power ports |
Weight |
5 kg, 11 pounds |
Dimensions |
9x43x56 cm, 3.5x17x22 inches |
Other Immunity Testing |
|
IEC 61000-4-11 |
AC voltage dips, interrupts and variations with optional EOS1 |
IEC 61000-4-13 |
Immunity to harmonics and interharmonics |
IEC 61000-4-14 |
Immunity to voltage fluctuations |
IEC 61000-4-17 |
Ripple on DC input power ports |
Weight |
5 kg, 11 pounds |
Dimensions |
9x43x56 cm, 3.5x17x22 inches |
NSG 1007-5 Power Supply |
|
Supply Option |
208 or 400 |
Operating Modes |
AC, DC, or AC + DC |
Frequency Range |
16Hz-1000Hz |
Total Power |
5kVA |
Load Power Factor |
0-1 at full rated power |
Output noise |
(20 kHz to 1 MHz) <250 mVrms typical, <500 mVrms maximum |
Harmonic distortion |
<1% from 16-66 Hz, <2% at 400 Hz, <3% at 800 Hz |
DC offset |
<20 mV |
External amplitude modulation |
Depth 0-10%, Frequency DC-2 kHz |
Isolation voltage |
300 Vrms output to chassis |
AC mode current |
|
Low range Steady state |
37.0 |
Low range Peak repetitive |
110.0 |
High range steady state |
18.5 |
High range peak repetive |
96.0 |
DC mode |
|
Supply option |
208 |
Maximum power |
3,500 Watts |
Output noise |
(20 kHz to 1 MHz) <250 mVrms typical, <500 mVrms Max |
Line regulation |
<0.1% FS for 10% Line change |
Packing List/Accessories
Included with Rental Of Teseq ProfLine 2105
Below you will find a list of common accessories that you can expect to be delivered with the equipment. This is a generic standard list and should you require an exact connector or accessory please contact us prior to order shipping. A detailed list of these can be found on the "All Accessories" tab.
ProfLine 2105
- NSG 1007
- CCN 1000-1
- Power Cable
- 4 Prong Power Cable for NSG 1007
- DB-37/68 PIN HD - PC to CCN Cable
- DB-9 Series Cable
- USB Cable
- Metal Terminal block Covers
- Cable Brackets
- 36 Pin Connectors
- Red & Blue Cables
- Red & Blue Wires
- 40VEU to US Plug (installed)
- 240V EU Power Plug
- Quick Instal
- Cal Instruction Tutorial
- Desktop Computer
- Power Supply with Cable
- Monitor
- Stand
- Display Port Cable
- USB Cable
- Shipping Case
Standards
Below is a list of common standards for Harmonics & Flicker Tester:
- EMC Directives
- IEC/EN 61000-3-2
- IEC/EN 61000-3-3
- IEC/EN 61000-4-8
- IEC/EN 61000-4-11
- IEC/EN 61000-4-13
- IEC/EN 61000-4-14
- IEC/EN 61000-4-17
- IEC/EN 61000-4-28
- IEC/EN 61000-4-29
- MIL STD 461
- RTCA/DO 160
ProfLine Series/Options
ProfLine Series Components
ProfLine 2105-208
- NSG 1007-5-208 Power source
- CCN 1000-1 1-phase coupling unit
- DAQ card
- Interface cable
- WIN 2100 H&F test software
- WIN 2110 PQT test software
- Pre-confi gured PC
- USB cable
ProfLine 2105-400
- NSG 1007-5-400 Power source
- CCN 1000-1 1-phase coupling unit
- DAQ card
- Interface cable
- WIN 2100 H&F test software
- WIN 2110 PQT test software
- Pre-confi gured PC
- USB cable
ProfLine Series Options | |
INA 2151 | 1-phase IEC 61000-3-3 16 Amp reference impedance |
CCN 1000-1L |
1-phase coupling unit with integrated IEC 61000-3-3 16 Amp impedance |
INA 2188 |
Rack mounting kit for CCN 1000-1 |
INA 2189 | Rack mounting kit for NSG 1007-5 |
WIN 2106 |
Test software for IEC 61000-3-11 and IEC 61000-3-12 |
Option 8 |
1 m magnetic loop antenna 100 A/m continuous and 300 A/m for 3 s |
Option 11-1 |
1-phase AC switch used to switch power between the source (set to the lower required voltage) and the mains supply in a time between 1-5 us. For details specification please see separate datasheet. |
Avionics |
Avionics immunity & emissions test capability for DO-160, Airbus and Boeing |
|