SAE J1455 - Automotive EMC Test Equipment Rentals
SAE J1455 - Automotive EMC Test Equipment Rentals
For automotive immunity testing, rentals provide a economical and time efficient solution for testing to this automotive standard by the Society of Automotive Engineers (SAE). This standard gives recommended practices and EMC testing methods for electrical environments from natural and vehicle-induced sources that influence the performance and reliability of vehicle and tractor/trailer electronic components. It also relates to stationary components which also use the vehicle-based components requirements. It is available for purchase on the SAE Website. This standard is aimed at being used during the design phase so as to develop Immunity system to commonly occurring environmental occurrences.  The sections of this standard that relate to electronics and EMC are k through m. Given the nature of truck and tractor systems three types of transients are tested for load dump, inductive switching, and mutual coupling. This standard often refers to SAE J1113 as a reference for EMI and EMC testing procedures and test levels.  SAE J1455 - Load dump waveform per ISO 7637
We offer automotive EMC test equipment solutions for all three main types of immunity-based testing requirements, load dump, inductive switching, and mutual coupling by this automotive standard. SAE J1455 references SAEJ1211 for electrostatic discharge testing. There is different transient voltage characteristics for 12 volt and 24 volt vehicle systems. These can be viewed in depth from table 4A and 4B, the major difference being in the open circuit. A basic summary of information for 12 volt systems per this standard can be seen below. SAE J1455 - Load dump, Inductive Switching and Mutual Test Levels
Rental equipment provide pulse testing abilities while limiting capital expenditures and learning curve associated with learning new test equipment. We carry automotive EMC test equipment from Teseq and EM Test, leaders in automotive test equipment. We offer the NSG 5500 and PA 5840 for the most comprehensive testing generators for a large variety of automotive based standards. The EM Test automotive immunity products, UCS200N, VDS200N, and LD200N provide testing for individual transient requirements. These EM Test automotive immunity products are cost effective solution for testing to individual pulses of SAE J1455. All of our automotive immunity test equipment rentals come with an A2LA accredited calibration, free technical support, and often a laptop to facilitate testing.  SAE J1455 - Automotive EMC Rental equipment

SAE J1455 Rentals - Automotive EMC Test Equipment

RENTAL

Automotive Immunity Generator Features 

      • ISO 7637-2 & OEM - Single Unit Solution!
      • Laptop with Software & ISO 17025 Calibration
      • Includes - +ARB, LD5550, MT5511, & Software
      • Free Technical Support & 2 Days Free Transit
      • PA 5480 (Batter Simulators) - 25A & 100A Rentals
      • Prorated Daily Rate After First Month
      • Turnkey Solution - Arrives Ready for Testing!

Overview

The Teseq NSG 5500 rental offers solutions for transient immunity testing based on ISO 7637-2 pulses 1, 2a, 3a, 3b, and the load dump pulses from ISO 16750-2.  It includes the +ARB Option for pulses 2b and 4. Our rental systems also have built in the MT5511, LD5550, +ARB, and come with Autostar Software with a laptop to control the unit(s). All of our automotive rentals include an accredited calibration in the rental price. This Teseq automotive transient generator includes a coupler/battery switch for testing requiring battery coupling. 

The NSG 5500 system allows for testing to international, commercial, and company specific standards including. The Arbitrary waveform generator option supports >64,000 segments plus 1GB of Clone data with up to 10Ms/s 16 bit operation. Control of the testing parameters is done through PC running AutoStar™ software. This Teseq automotive immunity generator rental offers testing to be completed through a single output connector.

This turnkey product comes with a laptop with software pre-installed for efficient testing. Additional inputs and outputs are located on the rear panel for test execution control purposes and monitoring. It is the first product to offer a completely internal 100 amp. battery switch for transient immunity testing. These rental transient immunity generators can be used with the PA 5840-300 battery Simulator or the PA 5840-75 Battery Simulator.

RENTAL

The PA5840-300 by Teseq is an 100 Amp DC power supply for use with the Teseq NSG 5500 automotive EMC immunity test system. A2LA accredited calibration is included in the automotive EMI immunity test equipment rental price. This fast, reliable, and modular battery simulator supply comes with up to 18 kW of power and is designed to simulate 12, 24, and 42 V vehicle electrical systems. 

This Automotive EMC Test Equipment provides dips and interrupts for a diverse set of automotive EMI standards including ISO 7637, waveforms 2b and 4. The PA 5840 also allows for testing to military automotive immunity standards including MIL-STD-461E. This latest Teseq model has 4 quadrant operation, important in the EV environment.

The PA 5840 includes two gain settings for use and output ranges for power efficiency. This DC power supply needs a control unit to be used.This automotive transient immunity generators setup also allows for High bandwidth up to 150 kHz. To facilitate the most efficient testing we provide rentals of both the 100 amp and the PA 5840-75 25 Amp model.  

SALE/RENTAL

ESD Gun Features

      • Air Discharge & Contact-discharge - 30kV (100V Steps)
      • Buy/Rent from Sole US Distributor!
      • IEC 61000-4-2 ESD Solution, 150pF/330Ω Network
      • Discharge detector, +/- Polarity, & Accessories available
      • Touch screen, Programmed Standards, Point & Test 
      • 2 Year Manufacturer Warranty on New Purchases
      • All Rentals - ISO 17025 Cal & 2 Days Transit Time

Overview

The Teseq NSG437 ESD gun allows for testing to 30kV air and contact (150pf/330Ω) with a simple and easy to use design. Transient Specialists is the only authorized sale partner of Teseq ESD simulators in the United States. It provides functions very similar to its competitors the Haefely ONYX 30 and the EM test ESD NX30.  It includes an accredited calibration and technical support is included in the rental equipment price. This equipment is an ideal solution for field testing as voltage levels can be easily modified for efficient testing to and above several standards.

This test equipment allows for manipulation of testing parameters for EN IEC 61000-4-2, ANSI C63.16 through the use of the display. It is designed to sit comfortably in the operator’s hand, with operating conditions constantly displayed and accessible on a bright, clear color touch display. This product is unique in offering an activity log where the number and type of simulations can be verified by time frame and standard.

The NSG 437 ESD Simulator has a color touch display and keypad for parameter input shows the precise functional and test data with user-selectable language for convenient and safe operation worldwide. The simulator contains variable threshold selection for accurate discharge detection. This detection feature can be switched off when testing EUT’s with non-conductive surfaces, such as plastic housings. This product is part of the Teseq electrostatic generator line of products including the NSG 435 and NSG 438.

Options:
  • Purchase New - In Stock $11,210.00
  • Rent 1 Week $495.00
  • Rent 1 Month $990.00

RENTAL

The Teseq NSG437 ESD simulator allows for testing to 30kv air and contact with a simple and easy to use design. A2LA accredited calibration and technical is included in the rental equipment price. This equipment comes with the INA4561 which provides a 100pf/1500 Ω discharge network (human body model).

This Teseq electrostatic discharge geneator allows for testing to MIL-STD-883, MIL-STD-464, and many other 30kV ESD specifications. It is designed to sit comfortably in the operator’s hand, with operating conditions constantly displayed and accessible on a bright, clear color touch display. This Teseq product is unique in offering an activity log where the number and type of simulations can be verified by time frame and standard.

The NSG 437 ESD Simulator has a color touch display and keypad for parameter input shows the precise functional and test data with user-selectable language for convenient and safe operation worldwide. It also contains variable threshold selection for accurate discharge detection. This detection feature can be switched off when testing EUT’s with non-conductive surfaces, such as plastic housings.

Out of Stock

SALE/RENTAL

Automotive ESD Gun Features

      • Automotive Teseq ESD Series - 30kV (100V Steps)
      • ISO 10605 & IEC 61000-4-2 Test Solution
      • Buy/Rent from Sole US Distributor!
      • Includes 4 Networks for Single Unit Solution
      • 150pf/330Ω, 330pf/330Ω, 150pf/2kΩ, & 330pf/2KΩ
      • Discharge detector, Adjustable +/- Polarity
      • 2 Year Manufacturer Warranty on New Purchases
      • All Rentals - ISO 17025 Cal & 2 Days Transit Time

Overview

The NSG 437 Auto is a variation on the popular 30kV Teseq series of ESD simulators/Guns. Rent and Buy it today from the only authorized sale partner of Teseq ESD simulators in the United States. This simulator/gun is provides testing to IEC 61000-4-2, ISO 10605, and many manufacturer standards. It comes standard with an ISO 17025 accredited calibration and up to two free days for transit. The three additional networks that are included with the standard NSG 437 simulator and 150pf/330Ω network are the 330pf/330Ω, 150pf/2kΩ, and 330pf/2KΩ.

Options:
  • Purchase New - In Stock $12,700.00
  • 1 Week Rental $645.00
  • 1 Month Rental $1,290.00