Home > Automotive EMC Test Equipment - EMI Rentals > EM Test VDS 200N30
EM Test VDS 200N30 - Front Side EM Test VDS 200N30 - Front EM Test VDS 200N30 - Back EM Test VDS 200N30 Side top
EM Test VDS 200N30 - Front Side
EM Test VDS 200N30 - Front
EM Test VDS 200N30 - Back
EM Test VDS 200N30 Side top

EM Test VDS 200N30

Rent 30 Amp Voltage Drop Simulator
  • Pulses 4 and 2b (ISO 7637-2/ISO 16750-2)
  • Maximum 60 Voltage 30 Amps
  • Voltage Drop Simulator with Low Output Impedance
  • Pre-programmed Test Routines
  • Current ISO 17025 Accredited Calibration

Included Accessories

  • Battery Simulator/Generator  
  • Power Cable
  • USB Interface Cable
  • Printed Manual
  • Calibration Documentation 
  • Short Introduction
  • USB Drive with License & Software
  • 125V Plug
  • (2) MC Connector Cable (red & black)
  • (2) Clamps Red & Black
  • Red Shipping Case
Can't find something? Contact Us
Got Questions? Speak to an Expert +1 630-887-0329
Two FREE days transit with every rental

Related Equipment

EM Test VDS 200Q50.2 - Front Side EM Test VDS 200Q50.2 - Front
EM Test VDS 200Q50.2
Rent 50 Amp Battery Simulator
EM Test VDS 200Q100.2 - Front Side EM Test VDS 200Q100.2 - Front
EM Test VDS 200Q100.2
Rent 100 Amp Battery Simulator
In Stock
EM Test AutoWave - Front Side EM Test AutoWave - Front
EM Test AutoWave
Rent 2 Channel Waveform Generator
In Stock
EM Test PFM 200N100 - Rent Automotive Power Fail Simulator EM Test PFM 200N100 - Rent Automotive Power Fail Simulator
EM Test PFM 200N100
Rent Automotive Power Fail Simulator
In Stock
EM Test VDS 200Q10 - Front Side Stock EM Test VDS 200Q10 - Front
EM Test VDS 200Q10
Rent 10 Amp Battery Simulator
EM Test VDS200N - Side EM Test VDS 200N15 - Rent 15 Amp Battery Simulator
EM Test VDS 200N15
Rent 15 Amp Battery Simulator

Description

The VDS 200N series is used to simulate the various battery supply waveforms recommended by international standards and by car manufacturer requirements. Especially the manufacturer requirements are an important area covered by the VDS 200N series as there is a large variety of requirements. Secondly, the VDS 200N series serve as powerful DC voltage supplies for the DUT during the tests with automotive transients. The VDS 200N series covers all three supply voltage categories. Their current capability ranges up to 200A depending on the model and your application.

Specifications:
Output Voltage
0V - 60V
Output Current
0A - 30A, continuous
Peak Current
15A
Frequency Range
DC to 100kHz
Supply Voltage
115/230V
Weight
49kg (108.02lbs)
Dimensions
19 Inches /6HU
COMMON DATA (ALL MODELS)
Ripple voltage
Ur <0.2Vp-p, frequency min. 400Hz
Source impedance
Zi = <10mohm
Sinusoidal signal capability vs. Frequency *)
Vpp max. 16V up to 20kHz Vpp max. 10V up to 30kHz Vpp max. 6V up to 50kHz
Vpp max. 3V up to 100kHz via Analog In, controlled by AutoWave/AMP 200Nx only
VDS 200N30.1 and VDS 200N50.1: Vpp max. 65V resp. 35V up to 50kHz with respect to the selected voltage range Vpp max. 3V up to 100kHz via Analog In, controlled by AutoWave/AMP 200Nx only
Fuses
Depending on VDS 200N model
TRIGGER
Automatic
Automatic release of the events
Manual
Manual release of a single pulse
External
External release of a single pulse
OUTPUT
DUT Supply +/-
Safety laboratory or high current connectors
Ext. trigger
5-15V TTL; BNC connector
CRO Trigger
5V TTL-signal for oscilloscope
TEST ROUTINES FOR ARBITRARY WAVES
DC source
Max. 60V; current depending on VDS 200N model
Functions
Sine Wave Sweep
Sine Wave (Cranking)
Clipped Load Dump
Jump Start
Extern
GM 9105P Pulse 4
Drop and Jump pulse
Standard Test routines
ISO 7637, Pulses 2b and 4 ISO 16750-2 Jaso Test 1
Service
Service, Setup, Self test
INTERFACE
Serial interfaxe
USB
Parallel interface
IEEE 488, addresses 1 - 30
Remote control
To connect an external signal generator (10kohm): 0-10V / 0-50kHz max. 0.5V(p-p) / 0-100kHz
Video Guides
EM Test VDS 200Q10 ISO 7637-2 Testing
Related Videos
OEM LV 124 Testing PA 5840, AutoWave, & PFM 200N
LV124 Testing with the EM Test VDS 200Q100.2 & Autowave
Documentation